| 0/0 |
2026/07/21 00:00 |
flow |
assessment-security |
42m
Results: map[DenialOfService:true Explanation:Based on the analysis of the bug report and the kernel source code, here is the
assessment of the issue:
### Root Cause Analysis
The bug report indicates a hung task (`INFO: task syz... blocked for more than
143 seconds`) where a process is stuck in `cgroup_lock_and_drain_offline()`.
This function is waiting on the `offline_waitq` for a cgroup subsystem state
(css) to finish offlining.
The offlining process is handled asynchronously by `css_killed_work_fn()`, which
is queued using `queue_rcu_work()`. This means the work is only scheduled
*after* an RCU grace period completes.
The NMI backtrace reveals that CPU 1 is simultaneously stuck in `io_serial_in()`
inside `serial8250_console_write()`. Because this is a `PREEMPT_RT` kernel,
standard spinlocks (like the `port->lock` acquired in
`serial8250_console_write`) are implemented as RT-mutexes which implicitly
acquire `rcu_read_lock()` to prevent RCU grace periods from completing while the
lock is held.
If the serial console's baud rate is set to an extremely low value (e.g., 50
baud), writing a single 1024-byte printk record to the console can take hundreds
of seconds. Because `serial8250_console_write()` holds the port lock (and thus
`rcu_read_lock()`) for the entire duration of writing that single record, it
blocks all RCU grace periods system-wide for that duration.
Since the RCU grace period cannot complete, `queue_rcu_work()` never queues the
cgroup offlining work, `offline_waitq` is never woken up, and the task waiting
in `cgroup_lock_and_drain_offline()` hangs, eventually triggering the hung task
detector.
### Security Impact
**Exploitable:** False. This is a pure concurrency/timing issue caused by a slow
hardware interface blocking RCU. There is no memory corruption, out-of-bounds
access, or information leak involved.
**Denial of Service:** True. The bug results in a system-wide RCU stall and hung
tasks, effectively causing a denial of service.
**Accessible From Unprivileged Processes / User Namespaces:** False. To trigger
this issue, an attacker must force `serial8250_console_write()` to take an
excessively long time for a single record. This requires setting the serial
console's baud rate to a very low value via `ioctl(TCSETS)`. The serial console
device node (e.g., `/dev/ttyS0`) is restricted to `root` or the `dialout` group.
Unprivileged users, even within user namespaces, do not have the necessary
permissions to open the physical console device and change its baud rate.
While unprivileged users might be able to trigger a large volume of `printk`
messages (e.g., by triggering warnings), the console flushing mechanism
(`console_flush_one_record`) releases the lock and enables interrupts/preemption
between individual records. Therefore, RCU grace periods can normally complete
between records unless a *single* record takes an abnormally long time (which
strictly requires a low baud rate).
### Conclusion
This is a known architectural limitation of slow serial consoles interacting
with RCU and `PREEMPT_RT` locking semantics. It causes a Denial of Service, but
it requires root/administrative privileges to misconfigure the serial port baud
rate, making it a non-issue for unprivileged local attackers. Exploitable:false FilesystemTrigger:false NetworkTrigger:false PeripheralTrigger:false RemoteTrigger:false Unprivileged:false UserNamespace:false VMGuestTrigger:false VMHostTrigger:false]
|
| 1/1 |
2026/07/21 00:00 |
action |
syz-repro-to-c-repro |
0m
Results:
|
| 2/1 |
2026/07/21 00:00 |
action |
kernel-checkouter |
1m
Results: map[KernelSrc:/app/workdir/cache/src/26766716579cdcff13b5e3416aa2d1ff891e8337]
|
| 3/1 |
2026/07/21 00:01 |
action |
kernel-builder |
23m
Results: map[KernelObj:/app/workdir/cache/build/f8a628c752ebc7bff60482a8688df256d2cc50bc]
|
| 4/1 |
2026/07/21 00:24 |
action |
codesearch-prepare |
11m
Results: map[Index:codesearch-index]
|
| 5/1 |
2026/07/21 00:36 |
agent |
expert |
5m
Model:
Results: map[DenialOfService:true Exploitable:false FilesystemTrigger:false NetworkTrigger:false PeripheralTrigger:false RemoteTrigger:false Unprivileged:false UserNamespace:false VMGuestTrigger:false VMHostTrigger:false]
Instruction: You are an experienced Linux kernel security engineer. Your task is to analyze given kernel bug report
and determine its security impact based on the following dimensions.
Use the provided tools to examine the source code, check for capability checks (e.g., capable(), ns_capable()),
and understand the nature of the bug. Analyze the given kernel build and configuration.
You can check the kernel config by grepping ".config" file; you can check kernel cmdline by grepping
".config" file for "CONFIG_CMDLINE=". Assume sysctl parameters have default values.
But analyze for the corresponding production build w/o debugging tools enabled (like KASAN, KMSAN, UBSAN).
Try different strategies when analyzing the bug:
- think of ways in which the vulnerable code is unreachable
- or the other way around: try to come up with different ideas of how an unprivileged user can reach the bug
If still unsure err on the side of the bug being non-exploitable/not-accessible.
In the final reply, provide a reasoning for your assessment.
Analysis dimensions:
* Exploitable:
Determine if the bug can result in memory corruption, elevated privileges, or an information leak.
Memory safety issues are almost always exploitable (KASAN or UBSAN reports for use-after-free, out-of-bounds;
refcounting issues, corrupted lists, etc). When kernel is crashing on a completely wild pointer access
(e.g. user-space address, or non-canonical address, but not on NULL or address corresponding to KASAN shadow
for NULL address), including both data accesses and control transfers, that also usually implies possibility
of exploitation. Such reports usually say "unable to handle kernel paging request".
Uses of uninitialized values detected by KMSAN may be exploitable b/c attacker frequently can affect uninit
values with spraying techniques. However, for these exploitability depends on how exactly the uninit value
is used in the code, and what it affects.
Information leaks are exploitable on their own and should be classified as such. A bug that copies kernel
memory contents to userspace (e.g. an out-of-bounds read whose result is returned to the caller, or
uninitialized stack/heap bytes written to a user buffer) is exploitable: it can reveal kernel pointer
values and defeat KASLR, expose sensitive data such as cryptographic keys or other processes' memory, and
serves as a necessary building block in most modern kernel privilege-escalation exploit chains. Do not classify
an information leak as non-exploitable solely because it does not directly cause a memory write or control-flow
hijack; the leak itself is the exploit primitive.
Think of what happens after the bug is triggered. Some bugs cause kernel panic and halt execution,
they are harder to exploit. For example, BUG reports halts the kernel. However, WARNING reports don't halt
execution in production builds. Debug bug detection tools (like KASAN, KMSAN, KCSAN, UBSAN) are also not enabled
in production builds, so attacker can freely exploit these bugs w/o being detected by these tools.
If you see an integer overflow, think how the overflowed value used later (if it's used as allocation size,
or an array index). If you see an out-of-bounds read, think if it's followed by an out-of-bounds write as well.
Some KCSAN data-races may be exploitable by skilled attackers as well. Think what data structures got corrupted
as the result of data races and how. However, note that kernel has lots of "benign" data races that don't lead
to any runtime misbehavior at all.
* Denial Of Service:
Determine if the bug can result in denial-of-service. Most bugs can, since they cause system crash,
hangs, deadlocks, or resource leaks. This is mostly applicable to WARNING bugs that won't cause system crash
in production. For these think what will be consequences of the violation of the kernel assumptions flagged
by the WARNING. In some cases the unexpected condition is also properly handled by the normal control flow
(e.g. with "if (WARN_ON(...))"), these won't cause denial-of-service. If the condition is not handled,
then it may or may not cause denial-of-service.
* Accessible From Unprivileged Processes:
Determine if the bug can be reached from a typical (non-root) user process that does NOT have any special capabilities
(like CAP_SYS_ADMIN, CAP_NET_ADMIN, CAP_NET_RAW, CAP_PERFMON) or access to device nodes restricted to root.
Assume that unprivileged_bpf_disabled=1, that is eBPF loading is not accessible. However, cBPF (classical BPF)
is still accessible to non-root processes.
Assume that user namespaces are not accessible, that is, the process cannot get the mentioned capabilities even
within a new user namespace (checked by ns_capable() function in the kernel sources).
* Accessible From User Namespaces:
Determine if the bug can be reached within a user-namespace where the process has all capabilities
(including CAP_SYS_ADMIN, CAP_NET_ADMIN, CAP_NET_RAW, CAP_PERFMON). Such capabilities are checked with ns_capable()
function in the kernel sources.
* VM Guest Trigger:
Determine if the bug can be triggered from the context of a typical KVM guest (e.g., set up by a QEMU VMM).
Consider accesses to standard Linux host paravirtualized features (virtio-blk, virtio-net, etc.),
and handling of VM exits in the KVM code.
* VM Host Trigger in The Confidential Computing Context:
Determine if the bug can be triggered in a confidential computing guest kernel from the context of a KVM host.
Consider access to standard Linux guest paravirtualized features (virtio-blk, virtio-net, etc.).
* Ethernet Network Trigger:
Determine if the bug can be triggered by processing ingress network Ethernet traffic, either directly (network stack)
or via drivers exposed to network data.
* Other Remote Trigger:
Determine if the bug can be triggered by processing remote traffic other than Ethernet (Wifi, Bluetooth, NFC, etc).
* Peripheral Trigger:
Determine if the bug can be triggered via an untrusted peripheral device that can be physically plugged
into a system, such as a USB device or a niche hardware driver handling external hardware inputs.
This is particularly important for mobile and desktop environments where users can plug in unknown devices.
* Malicious Filesystem Trigger:
Determine if the bug can be triggered by the kernel mounting and parsing a malicious filesystem image.
This is highly critical for Desktop and Mobile environments where external media or downloaded images
might be auto-mounted.
Don't make assumptions about the kernel source code (it may be different from what you assume it is).
Extensively use the provided code access tools (codesearch-*, git-*, grepper, etc)
to examine the actual source code, and confirm any assumptions.
Prefer calling several tools at the same time to save round-trips.
Use set-results tool to provide results of the analysis.
It must be called exactly once before the final reply.
Ignore results of this tool.
Prompt:
The kernel bug report is:
INFO: task syz.4.1502:10156 blocked for more than 143 seconds.
Tainted: G L syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.1502 state:D stack:27352 pid:10156 tgid:10155 ppid:6521 task_flags:0x400040 flags:0x00080002
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5510 [inline]
__schedule+0x1709/0x5530 kernel/sched/core.c:7231
__schedule_loop kernel/sched/core.c:7308 [inline]
schedule+0x164/0x2b0 kernel/sched/core.c:7323
cgroup_lock_and_drain_offline+0x51a/0x650 kernel/cgroup/cgroup.c:3275
cgroup_kn_lock_live+0x120/0x230 kernel/cgroup/cgroup.c:1715
cgroup_s[ 508.505874][ T39] cgroup_subtree_control_write+0x4b5/0x1080 kernel/cgroup/cgroup.c:3577
cgroup_file_write+0x331/0x8f0 kernel/cgroup/cgroup.c:4316
kernfs_fop_write_iter+0x3a5/0x540 fs/kernfs/file.c:345
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x61e/0xbb0 fs/read_write.c:687
ksys_write+0x156/0x270 fs/read_write.c:739
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x17b/0x530 arch/x86/entry/syscall_64.c:85
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fee1d10de99
RSP: 002b:00007fee1b366028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007fee1d395fa0 RCX: 00007fee1d10de99
RDX: 0000000000000005 RSI: 0000200000000040 RDI: 000000000000000c
RBP: 00007fee1d1a3eaf R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fee1d396038 R14: 00007fee1d395fa0 R15: 00007ffdeceae508
</TASK>
Showing all locks held in the system:
locks held by kworker/0:1/10: 6, last CPU#0:
#0: ffff88805bea4d38 ((wq_completion)wg-crypt-wg2#3){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88805bea4d38 ((wq_completion)wg-crypt-wg2#3){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88805bea4d38 ((wq_completion)wg-crypt-wg2#3){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc900000f7c60 ((work_completion)(&({ do { const void *__vpp_verify = (typeof((worker) + 0))((void *)0); (void)__vpp_verify; } while (0); ((typeof((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))))((unsigned long)((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))) + (((__per_cpu_offset[(cpu)]))))); })->work)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc900000f7c60 ((work_completion)(&({ do { const void *__vpp_verify = (typeof((worker) + 0))((void *)0); (void)__vpp_verify; } while (0); ((typeof((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))))((unsigned long)((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))) + (((__per_cpu_offset[(cpu)]))))); })->work)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc900000f7c60 ((work_completion)(&({ do { const void *__vpp_verify = (typeof((worker) + 0))((void *)0); (void)__vpp_verify; } while (0); ((typeof((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))))((unsigned long)((__typeof_unqual__(*((worker))) *)(( unsigned long)((worker)))) + (((__per_cpu_offset[(cpu)]))))); })->work)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __local_bh_disable_ip+0x3c/0x420 kernel/softirq.c:163
#3: ffff8880b863a958 (&pool->cb_lock){+...}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#3: ffff8880b863a958 (&pool->cb_lock){+...}-{3:3}, at: worker_lock_callback kernel/workqueue.c:3188 [inline]
#3: ffff8880b863a958 (&pool->cb_lock){+...}-{3:3}, at: bh_worker+0x8a/0x9a0 kernel/workqueue.c:3745
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __rt_spin_lock kernel/locking/spinlock_rt.c:50 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_spin_lock+0x1e0/0x400 kernel/locking/spinlock_rt.c:57
#5: ffff88813fe61d38 ((wq_completion)events_bh){+...}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#5: ffff88813fe61d38 ((wq_completion)events_bh){+...}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#5: ffff88813fe61d38 ((wq_completion)events_bh){+...}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
locks held by pr/legacy/17: 4, last CPU#1:
#0: ffffffff8e3b5a40 (console_lock){+.+.}-{0:0}, at: legacy_kthread_func+0x1a3/0x250 kernel/printk/printk.c:3718
#1: ffffffff8e29d338 (console_srcu){....}-{0:0}, at: rcu_try_lock_acquire include/linux/rcupdate.h:305 [inline]
#1: ffffffff8e29d338 (console_srcu){....}-{0:0}, at: srcu_read_lock_nmisafe include/linux/srcu.h:428 [inline]
#1: ffffffff8e29d338 (console_srcu){....}-{0:0}, at: console_srcu_read_lock kernel/printk/printk.c:291 [inline]
#1: ffffffff8e29d338 (console_srcu){....}-{0:0}, at: console_flush_one_record+0xfa/0xb90 kernel/printk/printk.c:3246
#2: ffffffff9a078558 (&port_lock_key){+.+.}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#2: ffffffff9a078558 (&port_lock_key){+.+.}-{3:3}, at: uart_port_lock_irqsave include/linux/serial_core.h:719 [inline]
#2: ffffffff9a078558 (&port_lock_key){+.+.}-{3:3}, at: serial8250_console_write+0x17c/0x1b40 drivers/tty/serial/8250/8250_port.c:3344
#3: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#3: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#3: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __rt_spin_lock kernel/locking/spinlock_rt.c:50 [inline]
#3: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_spin_lock+0x1e0/0x400 kernel/locking/spinlock_rt.c:57
locks held by ktimers/1/30: 7, last CPU#1:
#0: ffff8880b873b8e0 (&rq->__lock){-...}-{2:2}, at: raw_spin_rq_lock_nested+0x2d/0x160 kernel/sched/core.c:667
#1: ffff8880b8724548 (psi_seq){-...}-{0:0}, at: psi_task_switch+0x57/0x7d0 kernel/sched/psi.c:933
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __rt_spin_lock kernel/locking/spinlock_rt.c:50 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_spin_lock+0x1e0/0x400 kernel/locking/spinlock_rt.c:57
#3: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_mutex_slowunlock+0xbf/0xa20 kernel/locking/rtmutex.c:1430
#4: ffff8880b8728458 (hrtimer_bases.lock){-...}-{2:2}, at: __run_hrtimer kernel/time/hrtimer.c:2069 [inline]
#4: ffff8880b8728458 (hrtimer_bases.lock){-...}-{2:2}, at: __hrtimer_run_queues+0x495/0xaf0 kernel/time/hrtimer.c:2122
#5: ffffffff99d06748 (&____s->seqcount#2){--..}-{0:0}, at: ktime_get+0x45/0x220 kernel/time/timekeeping.c:998
#6: ffff8880b8728458 (hrtimer_bases.lock){-...}-{2:2}, at: lock_hrtimer_base kernel/time/hrtimer.c:192 [inline]
#6: ffff8880b8728458 (hrtimer_bases.lock){-...}-{2:2}, at: hrtimer_start_range_ns+0x8c/0x3f0 kernel/time/hrtimer.c:1526
locks held by khungtaskd/39: 1, last CPU#0:
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: debug_show_all_locks+0x2e/0x180 kernel/locking/lockdep.c:6835
locks held by udevd/4956: 7, last CPU#1:
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: sock_def_readable+0xae/0x550 net/core/sock.c:3656
#1: ffff888040d12298 (&si->socket.wq.wait){+.+.}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#1: ffff888040d12298 (&si->socket.wq.wait){+.+.}-{3:3}, at: __wake_up_common_lock+0x2f/0x1f0 kernel/sched/wait.c:124
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __rt_spin_lock kernel/locking/spinlock_rt.c:50 [inline]
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_spin_lock+0x1e0/0x400 kernel/locking/spinlock_rt.c:57
#3: ffff888061503208 (&ep->lock){+.+.}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#3: ffff888061503208 (&ep->lock){+.+.}-{3:3}, at: ep_poll_callback+0x79/0x7e0 fs/eventpoll.c:1484
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: list_lru_del_obj+0xbe/0x270 mm/list_lru.c:283
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: lock_list_lru_of_memcg+0x30/0x4a0 mm/list_lru.c:92
#6: ffff888036bdfc30 (_T->lock){....}-{2:2}, at: rt_mutex_slowunlock+0xbf/0xa20 kernel/locking/rtmutex.c:1430
locks held by getty/5344: 2, on CPU#0:
#0: ffff888036acb0a0 (&tty->ldisc_sem){++++}-{0:0}, at: tty_ldisc_ref_wait+0x25/0x70 drivers/tty/tty_ldisc.c:243
#1: ffffc900044cb2e0 (&ldata->atomic_read_lock){+.+.}-{4:4}, at: n_tty_read+0x460/0x1360 drivers/tty/n_tty.c:2211
locks held by udevd/5614: 4, on CPU#0:
#0: ffff888037977b80 (&p->lock){+.+.}-{4:4}, at: seq_read_iter+0xa5/0xcb0 fs/seq_file.c:183
#1: ffff8880336c1878 (&of->mutex#2){+.+.}-{4:4}, at: kernfs_seq_start+0x5d/0x420 fs/kernfs/file.c:165
#2: ffff88805ddfeb48 (kn->active#29){++++}-{0:0}, at: kernfs_get_active_of fs/kernfs/file.c:73 [inline]
#2: ffff88805ddfeb48 (kn->active#29){++++}-{0:0}, at: kernfs_seq_start+0xb2/0x420 fs/kernfs/file.c:166
#3: ffff88803d50a210 (&dev->mutex){....}-{4:4}, at: device_lock_interruptible include/linux/device.h:1109 [inline]
#3: ffff88803d50a210 (&dev->mutex){....}-{4:4}, at: manufacturer_show+0x26/0xa0 drivers/usb/core/sysfs.c:142
locks held by kworker/1:6/5770: 5, last CPU#1:
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc900056b7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc900056b7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc900056b7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffff88802a3e0210 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#2: ffff88802a3e0210 (&dev->mutex){....}-{4:4}, at: hub_event+0x187/0x4cf0 drivers/usb/core/hub.c:5899
#3: ffff88803d50a210 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#3: ffff88803d50a210 (&dev->mutex){....}-{4:4}, at: __device_attach+0x88/0x450 drivers/base/dd.c:1073
#4: ffff88805c5671d8 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#4: ffff88805c5671d8 (&dev->mutex){....}-{4:4}, at: __device_attach+0x88/0x450 drivers/base/dd.c:1073
locks held by kworker/1:8/5797: 6, on CPU#1:
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc90005807c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc90005807c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc90005807c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffff88802a568210 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#2: ffff88802a568210 (&dev->mutex){....}-{4:4}, at: hub_event+0x187/0x4cf0 drivers/usb/core/hub.c:5899
#3: ffff88802a578658 (&port_dev->status_lock){+.+.}-{4:4}, at: usb_lock_port drivers/usb/core/hub.c:3252 [inline]
#3: ffff88802a578658 (&port_dev->status_lock){+.+.}-{4:4}, at: hub_port_connect drivers/usb/core/hub.c:5464 [inline]
#3: ffff88802a578658 (&port_dev->status_lock){+.+.}-{4:4}, at: hub_port_connect_change drivers/usb/core/hub.c:5707 [inline]
#3: ffff88802a578658 (&port_dev->status_lock){+.+.}-{4:4}, at: port_event drivers/usb/core/hub.c:5871 [inline]
#3: ffff88802a578658 (&port_dev->status_lock){+.+.}-{4:4}, at: hub_event+0x20ad/0x4cf0 drivers/usb/core/hub.c:5953
#4: ffff88802a598158 (hcd->address0_mutex){+.+.}-{4:4}, at: hub_port_connect drivers/usb/core/hub.c:5465 [inline]
#4: ffff88802a598158 (hcd->address0_mutex){+.+.}-{4:4}, at: hub_port_connect_change drivers/usb/core/hub.c:5707 [inline]
#4: ffff88802a598158 (hcd->address0_mutex){+.+.}-{4:4}, at: port_event drivers/usb/core/hub.c:5871 [inline]
#4: ffff88802a598158 (hcd->address0_mutex){+.+.}-{4:4}, at: hub_event+0x20e1/0x4cf0 drivers/usb/core/hub.c:5953
#5: ffffffff8f06a920 (ehci_cf_port_reset_rwsem){.+.+}-{4:4}, at: hub_port_reset+0x14d/0x1800 drivers/usb/core/hub.c:3067
locks held by kworker/u8:36/9629: 2, last CPU#0:
#0: ffff888031fb5138 ((wq_completion)bat_events){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff888031fb5138 ((wq_completion)bat_events){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff888031fb5138 ((wq_completion)bat_events){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc9000db47c60 ((work_completion)(&(&bat_priv->dat.work)->work)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc9000db47c60 ((work_completion)(&(&bat_priv->dat.work)->work)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc9000db47c60 ((work_completion)(&(&bat_priv->dat.work)->work)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
locks held by kworker/u8:63/10003: 5, last CPU#0:
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc9000faf7c60 ((work_completion)(&(&nsim_dev->trap_data->trap_report_dw)->work)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc9000faf7c60 ((work_completion)(&(&nsim_dev->trap_data->trap_report_dw)->work)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc9000faf7c60 ((work_completion)(&(&nsim_dev->trap_data->trap_report_dw)->work)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffff88805ba4c310 (&devlink->lock_key#8){+.+.}-{4:4}, at: nsim_dev_trap_report_work+0x57/0xcb0 drivers/net/netdevsim/dev.c:909
#3: ffff888076174d20 (&nsim_trap_data->trap_lock){+.+.}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#3: ffff888076174d20 (&nsim_trap_data->trap_lock){+.+.}-{3:3}, at: nsim_dev_trap_report drivers/net/netdevsim/dev.c:862 [inline]
#3: ffff888076174d20 (&nsim_trap_data->trap_lock){+.+.}-{3:3}, at: nsim_dev_trap_report_work+0x1e0/0xcb0 drivers/net/netdevsim/dev.c:922
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __rt_spin_lock kernel/locking/spinlock_rt.c:50 [inline]
#4: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rt_spin_lock+0x1e0/0x400 kernel/locking/spinlock_rt.c:57
locks held by kworker/u8:64/10004: 7, last CPU#0:
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88801aea4138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc9000fb07c60 ((work_completion)(&(&kfence_timer)->work)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc9000fb07c60 ((work_completion)(&(&kfence_timer)->work)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc9000fb07c60 ((work_completion)(&(&kfence_timer)->work)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffffffff8e251c70 (cpu_hotplug_lock){++++}-{0:0}, at: static_key_enable+0x12/0x20 kernel/jump_label.c:222
#3: ffffffff8e4995d8 (jump_label_mutex){+.+.}-{4:4}, at: jump_label_lock kernel/jump_label.c:27 [inline]
#3: ffffffff8e4995d8 (jump_label_mutex){+.+.}-{4:4}, at: static_key_enable_cpuslocked+0xcb/0x240 kernel/jump_label.c:207
#4: ffffffff8e268598 (text_mutex){+.+.}-{4:4}, at: arch_jump_label_transform_apply+0x17/0x30 arch/x86/kernel/jump_label.c:145
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#5: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __pte_offset_map+0x29/0x200 mm/pgtable-generic.c:290
#6: ffff88801ae98c58 (ptlock_ptr(ptdesc)#2){+.+.}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#6: ffff88801ae98c58 (ptlock_ptr(ptdesc)#2){+.+.}-{3:3}, at: pte_offset_map_lock+0x13d/0x210 mm/pgtable-generic.c:404
locks held by syz.4.1502/10156: 3, on CPU#1:
#0: ffff888021ba4728 (&f->f_pos_lock){+.+.}-{4:4}, at: fdget_pos+0x252/0x320 fs/file.c:1259
#1: ffff888037194510 (sb_writers#9){.+.+}-{0:0}, at: file_start_write include/linux/fs.h:2731 [inline]
#1: ffff888037194510 (sb_writers#9){.+.+}-{0:0}, at: vfs_write+0x231/0xbb0 fs/read_write.c:683
#2: ffff88803d6b3478 (&of->mutex){+.+.}-{4:4}, at: kernfs_fop_write_iter+0x1d9/0x540 fs/kernfs/file.c:336
locks held by kworker/0:8/10753: 3, on CPU#0:
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc90006cb7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc90006cb7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc90006cb7c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffff88802a538210 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#2: ffff88802a538210 (&dev->mutex){....}-{4:4}, at: hub_event+0x187/0x4cf0 drivers/usb/core/hub.c:5899
locks held by kworker/0:11/10756: 5, last CPU#0:
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#0: ffff88802068d938 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#1: ffffc90007227c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:300 [inline]
#1: ffffc90007227c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:840 [inline]
#1: ffffc90007227c60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x7fd/0x1480 kernel/workqueue.c:3344
#2: ffff88802a518210 (&dev->mutex){....}-{4:4}, at: device_lock include/linux/device.h:1104 [inline]
#2: ffff88802a518210 (&dev->mutex){....}-{4:4}, at: hub_event+0x187/0x4cf0 drivers/usb/core/hub.c:5899
#3: ffff88801aeaf238 (&root->kernfs_rwsem){++++}-{4:4}, at: kernfs_add_one+0x41/0x5e0 fs/kernfs/dir.c:825
#4: ffff88801aeaf2c0 (&root->kernfs_iattr_rwsem){++++}-{4:4}, at: kernfs_link_sibling+0x4c7/0x5a0 fs/kernfs/dir.c:411
locks held by syz.8.2034/12329: 3, last CPU#0:
#0: ffff888033ab2b38 (&sb->s_type->i_mutex_key#12){+.+.}-{4:4}, at: inode_lock include/linux/fs.h:1024 [inline]
#0: ffff888033ab2b38 (&sb->s_type->i_mutex_key#12){+.+.}-{4:4}, at: __sock_release+0x7a/0x1f0 net/socket.c:738
#1: ffffffff8e259320 (local_bh){.+.+}-{1:3}, at: __local_bh_disable_ip+0x3c/0x420 kernel/softirq.c:163
#2: ffffffff8e3c3880 (rcu_read_lock){....}-{1:3}, at: __local_bh_disable_ip+0x3c/0x420 kernel/softirq.c:163
locks held by dhcpcd-run-hook/12346: 1, last CPU#0:
#0: ffff8880877a9588 (vm_lock){++++}-{0:0}, at: spin_lock include/linux/spinlock_rt.h:45 [inline]
#0: ffff8880877a9588 (vm_lock){++++}-{0:0}, at: __refill_objects_node+0x4e2/0x5b0 mm/slub.c:7227
=============================================
NMI backtrace for cpu 0
CPU: 0 UID: 0 PID: 39 Comm: khungtaskd Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/09/2026
Call Trace:
<TASK>
dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120
nmi_cpu_backtrace+0x274/0x2d0 lib/nmi_backtrace.c:122
nmi_trigger_cpumask_backtrace+0x17a/0x380 lib/nmi_backtrace.c:65
trigger_all_cpu_backtrace include/linux/nmi.h:162 [inline]
__sys_info lib/sys_info.c:157 [inline]
sys_info+0x135/0x170 lib/sys_info.c:165
check_hung_uninterruptible_tasks kernel/hung_task.c:353 [inline]
watchdog+0xfd7/0x1030 kernel/hung_task.c:561
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 UID: 0 PID: 17 Comm: pr/legacy Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/09/2026
RIP: 0010:io_serial_in+0x77/0xc0 drivers/tty/serial/8250/8250_port.c:401
Code: e8 6e 3b 65 fc 44 89 f9 d3 e3 49 83 ee 80 4c 89 f0 48 c1 e8 03 42 80 3c 20 00 74 08 4c 89 f7 e8 2f 92 d1 fc 41 03 1e 89 da ec <0f> b6 c0 5b 41 5c 41 5e 41 5f c3 cc cc cc cc cc 44 89 f9 80 e1 07
RSP: 0018:ffffc90000167a28 EFLAGS: 00000202
RAX: 1ffffffff340f000 RBX: 00000000000003fd RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000000 RDI: 0000000000000000
RBP: dffffc0000000000 R08: 0000000000000000 R09: 0000000000000000
R10: dffffc0000000000 R11: ffffffff856067f0 R12: dffffc0000000000
R13: 0000000000000000 R14: ffffffff9a078580 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff888125af2000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f5f37a31700 CR3: 0000000037464000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 00000000000f010e DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
serial_in drivers/tty/serial/8250/8250.h:128 [inline]
serial_lsr_in drivers/tty/serial/8250/8250.h:150 [inline]
wait_for_lsr+0x190/0x300 drivers/tty/serial/8250/8250_port.c:1982
serial8250_fifo_wait_for_lsr_thre drivers/tty/serial/8250/8250_port.c:3235 [inline]
serial8250_console_fifo_write drivers/tty/serial/8250/8250_port.c:3300 [inline]
serial8250_console_write+0x113a/0x1b40 drivers/tty/serial/8250/8250_port.c:3385
console_emit_next_record kernel/printk/printk.c:3163 [inline]
console_flush_one_record+0x667/0xb90 kernel/printk/printk.c:3268
legacy_kthread_func+0x1b6/0x250 kernel/printk/printk.c:3719
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Reply: Based on the analysis of the bug report and the kernel source code, here is the assessment of the issue:
### Root Cause Analysis
The bug report indicates a hung task (`INFO: task syz... blocked for more than 143 seconds`) where a process is stuck in `cgroup_lock_and_drain_offline()`. This function is waiting on the `offline_waitq` for a cgroup subsystem state (css) to finish offlining.
The offlining process is handled asynchronously by `css_killed_work_fn()`, which is queued using `queue_rcu_work()`. This means the work is only scheduled *after* an RCU grace period completes.
The NMI backtrace reveals that CPU 1 is simultaneously stuck in `io_serial_in()` inside `serial8250_console_write()`. Because this is a `PREEMPT_RT` kernel, standard spinlocks (like the `port->lock` acquired in `serial8250_console_write`) are implemented as RT-mutexes which implicitly acquire `rcu_read_lock()` to prevent RCU grace periods from completing while the lock is held.
If the serial console's baud rate is set to an extremely low value (e.g., 50 baud), writing a single 1024-byte printk record to the console can take hundreds of seconds. Because `serial8250_console_write()` holds the port lock (and thus `rcu_read_lock()`) for the entire duration of writing that single record, it blocks all RCU grace periods system-wide for that duration.
Since the RCU grace period cannot complete, `queue_rcu_work()` never queues the cgroup offlining work, `offline_waitq` is never woken up, and the task waiting in `cgroup_lock_and_drain_offline()` hangs, eventually triggering the hung task detector.
### Security Impact
**Exploitable:** False. This is a pure concurrency/timing issue caused by a slow hardware interface blocking RCU. There is no memory corruption, out-of-bounds access, or information leak involved.
**Denial of Service:** True. The bug results in a system-wide RCU stall and hung tasks, effectively causing a denial of service.
**Accessible From Unprivileged Processes / User Namespaces:** False. To trigger this issue, an attacker must force `serial8250_console_write()` to take an excessively long time for a single record. This requires setting the serial console's baud rate to a very low value via `ioctl(TCSETS)`. The serial console device node (e.g., `/dev/ttyS0`) is restricted to `root` or the `dialout` group. Unprivileged users, even within user namespaces, do not have the necessary permissions to open the physical console device and change its baud rate.
While unprivileged users might be able to trigger a large volume of `printk` messages (e.g., by triggering warnings), the console flushing mechanism (`console_flush_one_record`) releases the lock and enables interrupts/preemption between individual records. Therefore, RCU grace periods can normally complete between records unless a *single* record takes an abnormally long time (which strictly requires a low baud rate).
### Conclusion
This is a known architectural limitation of slow serial consoles interacting with RCU and `PREEMPT_RT` locking semantics. It causes a Denial of Service, but it requires root/administrative privileges to misconfigure the serial port baud rate, making it a non-issue for unprivileged local attackers.
|
| 6/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 18664
output: 43
thoughts: 983
Thoughts: **Analyzing a Hung Task and Serial Console Issues**
Okay, so I've got a hung task report here, `syz.4.1502:10156`, blocked for over two minutes, which is concerning. The call trace points directly to `cgroup_lock_and_drain_offline`, and that immediately raises a flag. We're in the realm of cgroup operations, and that function specifically deals with draining tasks from a cgroup during an offline operation. Something's clearly holding a lock within the cgroup code, preventing this process from continuing.
But then, there's an NMI backtrace from CPU 1, which adds another layer to this mystery. It shows a seemingly unrelated function, `io_serial_in`, which is part of the serial console driver, deeply nested in `wait_for_lsr`. This suggests a potential problem with the serial console itself. We are in the `serial8250_console_write` function which writes to the console.
Now, that's interesting. A hung task in cgroup code AND a potential serial console stall? These could be related. If the serial console is exceptionally slow, it could be causing system-wide delays or blocking processes. It's not uncommon for printk output to contend for resources, especially if there's excessive logging. Could the cgroup lock be somehow related to waiting on the slow console output? Perhaps the system is trying to log something about the cgroup operation or failure to the console and is getting stuck.
My next step would be to delve deeper into `cgroup_lock_and_drain_offline` and see what it is actually doing and what locks it's acquiring. I'll need to examine the cgroup code path and trace how it interacts with the console and the blocking process, to see if there's contention between the two. Also, if possible, I need to review the console output, which might provide more clues. I'll also check if the serial console driver is configured correctly and how busy it is.
|
| 7/2 |
2026/07/21 00:36 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:cgroup_lock_and_drain_offline]
Results: map[SourceCode:3243: /**
3244: * cgroup_lock_and_drain_offline - lock cgroup_mutex and drain offlined csses
3245: * @cgrp: root of the target subtree
3246: *
3247: * Because css offlining is asynchronous, userland may try to re-enable a
3248: * controller while the previous css is still around. This function grabs
3249: * cgroup_mutex and drains the previous css instances of @cgrp's subtree.
3250: */
3251: void cgroup_lock_and_drain_offline(struct cgroup *cgrp)
3252: __acquires(&cgroup_mutex)
3253: {
3254: struct cgroup *dsct;
3255: struct cgroup_subsys_state *d_css;
3256: struct cgroup_subsys *ss;
3257: int ssid;
3258:
3259: restart:
3260: cgroup_lock();
3261:
3262: cgroup_for_each_live_descendant_post(dsct, d_css, cgrp) {
3263: for_each_subsys(ss, ssid) {
3264: struct cgroup_subsys_state *css = cgroup_css(dsct, ss);
3265: DEFINE_WAIT(wait);
3266:
3267: if (!css || !css_is_dying(css))
3268: continue;
3269:
3270: cgroup_get_live(dsct);
3271: prepare_to_wait(&dsct->offline_waitq, &wait,
3272: TASK_UNINTERRUPTIBLE);
3273:
3274: cgroup_unlock();
3275: schedule();
3276: finish_wait(&dsct->offline_waitq, &wait);
3277:
3278: cgroup_put(dsct);
3279: goto restart;
3280: }
3281: }
3282: }
SourceFile:kernel/cgroup/cgroup.c]
|
| 8/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 20741
output: 49
thoughts: 745
Thoughts: **Debugging a Stalled Task**
Okay, so I've got this task, it's sitting in `schedule()` at line 3275. It's waiting on `dsct->offline_waitq`, which, from what I know, should be woken up when a cgroup goes offline. The problem is, this task has been blocked for 143 seconds now, so it seems like that offlining process isn't happening. That's a red flag.
The question then is, *why* isn't the CSS offlining? Something must be holding it up. My first instinct is to check for lock contention. I need to see what locks are currently held by other tasks.
Let's see... `kworker/0:1/10` has `wg-crypt-wg2#3` and `rcu_read_lock`. Okay, nothing immediately alarming there. Then `pr/legacy/17` is holding `console_lock`, `console_srcu`, `port_lock_key`, and `rcu_read_lock`. Interesting, but not screaming "blocker" yet. `ktimers/1/30` has `rq->__lock`, `psi_seq`, `rcu_read_lock`, `hrtimer_bases.lock`, and `____s->seqcount#2`... still, nothing stands out. Now, `udevd/4956` is holding `rcu_read_lock`, `si->socket.wq.wait`, `ep->lock`, and `_T->lock`. Okay, onto the next one.
`kworker/1:8/5797` has `usb_hub_wq`, `hub->events`, `dev->mutex`, `port_dev->status_lock`, `hcd->address0_mutex`, and `ehci_cf_port_reset_rwsem`. Nothing obviously blocking there. And finally, `kworker/u8:63/10003` holds `events_unbound`, `nsim_dev->trap_data->trap_report_dw`, `devlink->lock_key#8`, `nsim_trap_data->trap_lock`, and `rcu_read_lock`. Still nothing definitive, but `rcu_read_lock` is quite common.
Hold on... `kworker/u8:64/10004` is the one to focus on! It's holding `events_unbound`, `kfence_timer`, `cpu_hotplug_lock`, `jump_label_mutex`, `text_mutex`, `rcu_read_lock`, and `ptlock_ptr(ptdesc)#2`. And it's doing something with `__pte_offset_map` -> `pte_offset_map_lock`. Why is it also holding `rcu_read_lock`? I'd like to dive into the stack but these are just lock held information, not a call graph.
But... wait a second. Looking back at the list, I see that `pr/legacy/17` is the problem. It seems to be stuck in `io_serial_in`. And `io_serial_in` is reading from the serial port. Right, if the serial port is being slow, or not responding, then `console_flush_one_record` can take a long time to return.
Ah ha! But `pr/legacy/17` is a kthread, which means it is linked to the console. Is this a known serial console issue? Indeed, `wait_for_lsr` can spin for a long time if the serial port is slow or not responding. Does `wait_for_lsr` have a timeout? Let's check.
|
| 9/2 |
2026/07/21 00:36 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:wait_for_lsr]
Results: map[SourceCode:1967: /* Returns true if @bits were set, false on timeout */
1968: static bool wait_for_lsr(struct uart_8250_port *up, int bits)
1969: {
1970: unsigned int status, tmout;
1971:
1972: /*
1973: * Wait for a character to be sent. Fallback to a safe default
1974: * timeout value if @frame_time is not available.
1975: */
1976: if (up->port.frame_time)
1977: tmout = up->port.frame_time * 2 / NSEC_PER_USEC;
1978: else
1979: tmout = 10000;
1980:
1981: for (;;) {
1982: status = serial_lsr_in(up);
1983:
1984: if ((status & bits) == bits)
1985: break;
1986: if (--tmout == 0)
1987: break;
1988: udelay(1);
1989: touch_nmi_watchdog();
1990: }
1991:
1992: return (tmout != 0);
1993: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 10/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 22758
output: 59
thoughts: 94
Thoughts: **Analyzing a Potential Performance Bottleneck**
Okay, so this `wait_for_lsr` function is using a busy-wait loop with `udelay(1)`. That's not ideal, especially if `tmout` gets big. Hmm, I wonder where `tmout` is getting its value? Ah, a potential connection β `up->port.frame_time` could be influencing it. Right, if `frame_time` is large, then `tmout` could also become significantly large, causing that spin loop to hang around for way too long. Hold on... what if `frame_time` is *really* huge? We could have a serious performance issue here. Time to track down where `frame_time` is actually being set and see if there are any reasonable limits or potential overflow problems. Let's dig deeper!
|
| 11/2 |
2026/07/21 00:36 |
tool |
codesearch-find-references |
0m
Error:
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c IncludeSnippetLines:0 Name:frame_time SourceTreePrefix:]
Results: map[References:<nil> TruncatedOutput:false]
|
| 12/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 23111
output: 63
thoughts: 17
Thoughts: Okay, here's my summary, presented as a stream of thought:
**Diving into the `uart_port` Structure**
Right, so I'm looking at this code and, aha, here it is: `frame_time`. That's tucked away inside the `uart_port` structure. Okay, so that means it's a field associated with a specific UART port, which is exactly what I'd expect. `uart_port` is the standard data structure for representing a serial port and its configuration within the kernel, so seeing timing information here makes perfect sense. I wonder how it's used. Is it related to the hardware's clock? Does it deal with timing for the RX or TX processes? Iβll have to dig deeper into the context to understand its specific function within the whole serial driver framework. It's good that it's clearly defined as a member of `uart_port`, at least. That provides a specific scope for its functionality. Now let's explore the references to frame_time.
|
| 13/2 |
2026/07/21 00:36 |
tool |
codesearch-find-references |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c IncludeSnippetLines:0 Name:uart_port::frame_time SourceTreePrefix:]
Results: map[References:[map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:__stop_tx SourceFile:drivers/tty/serial/8250/8250_port.c SourceLine:1392] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:__stop_tx SourceFile:drivers/tty/serial/8250/8250_port.c SourceLine:1392] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:dw8250_wait_re_deassert SourceFile:drivers/tty/serial/8250/8250_dwlib.c SourceLine:70] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:uart_fifo_timeout SourceFile:include/linux/serial_core.h SourceLine:1045] map[ReferenceKind:writes ReferencingEntityKind:function ReferencingEntityName:uart_update_timeout SourceFile:drivers/tty/serial/serial_core.c SourceLine:451] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:uart_wait_until_sent SourceFile:drivers/tty/serial/serial_core.c SourceLine:1770] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:wait_for_lsr SourceFile:drivers/tty/serial/8250/8250_port.c SourceLine:1976] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:wait_for_lsr SourceFile:drivers/tty/serial/8250/8250_port.c SourceLine:1977]] TruncatedOutput:false]
|
| 14/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 24223
output: 40
thoughts: 11
Thoughts: Okay, let's dive into this. Here's my take on those thoughts, as if they're my own:
**Analyzing `uart_update_timeout`**
Alright, so the focus is on `uart_update_timeout`. Immediately, I'm thinking about the implications. This function likely manages the time window allowed for UART communication. Given that UART is a serial communication protocol, timeout management is *critical* for ensuring reliable data transmission, preventing blocking on unresponsive devices, and handling potential errors gracefully.
My mind immediately starts running through possible scenarios. What exactly does "update" mean in this context? Is it modifying an existing timeout value based on something like baud rate, data length, or even detected link quality? Or is it simply setting a *new* timeout value entirely? The granularity of the update is important, of course. Is it coarse-grained, a few fixed values, or more fine-grained, allowing adjustments down to the millisecond or even microsecond level?
I also consider the potential inputs. What parameters does `uart_update_timeout` accept? A pointer to a UART control structure, definitely. But what else? The new timeout value itself (in some appropriate unit like milliseconds or clock cycles, depending on the hardware) is a given. Does it also handle other parameters, like the type of timeout? For instance, does it differentiate between timeouts for character reception versus overall frame completion? Error management is key to this. How does it handle illegal values, negative timeouts, or other pathological inputs? Does it return an error code or just silently fail?
And, most importantly, what are the *consequences* of calling this function? Does it involve disabling interrupts, modifying hardware registers, or manipulating internal state variables? Are there any race conditions I need to worry about if this function is called from an interrupt context or multiple threads? Is this an atomic operation?
I also think about how it's *used*. Where in the system is this function called from? Is it part of the initialization sequence, called periodically in a polling loop, or triggered by an interrupt? Understanding the calling context will shed light on what its intended purpose is and its relationship to other functionalities like flow control.
Ultimately, I'm going to have to look at the implementation details, but all of these questions are swimming in my head as I prepare to analyze it. Now, let's see the code!
|
| 15/2 |
2026/07/21 00:36 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/serial_core.c Name:uart_update_timeout]
Results: map[SourceCode: 432: /**
433: * uart_update_timeout - update per-port frame timing information
434: * @port: uart_port structure describing the port
435: * @cflag: termios cflag value
436: * @baud: speed of the port
437: *
438: * Set the @port frame timing information from which the FIFO timeout value is
439: * derived. The @cflag value should reflect the actual hardware settings as
440: * number of bits, parity, stop bits and baud rate is taken into account here.
441: *
442: * Locking: caller is expected to take @port->lock
443: */
444: void
445: uart_update_timeout(struct uart_port *port, unsigned int cflag,
446: unsigned int baud)
447: {
448: u64 temp = tty_get_frame_size(cflag);
449:
450: temp *= NSEC_PER_SEC;
451: port->frame_time = (unsigned int)DIV64_U64_ROUND_UP(temp, baud);
452: }
SourceFile:drivers/tty/serial/serial_core.c]
|
| 16/2 |
2026/07/21 00:36 |
llm |
expert |
0m
Model:
Tokens:
input: 25138
output: 50
thoughts: 508
Thoughts: **Analyzing a Potential Soft Lockup in the Serial Driver**
Okay, let's break this down. If the `baud` rate is set incredibly low, the `frame_time` becomes very large. I see that `baud` is passed to `uart_update_timeout`, so it's directly influencing that calculation. The question is, what's the minimum allowable baud rate? If it's as low as 1, then the `frame_time` balloons to a staggering 10 seconds (10^10 nanoseconds).
Now, this `frame_time` is used to calculate the timeout, `tmout`. A quick calculation gives us a timeout of `20,000,000` microseconds, or 20 seconds. This is critical because `wait_for_lsr` relies on this timeout value. My initial thought was that this wait time was per *character*, and that's concerning. Digging further, it appears `wait_for_lsr` is called within `serial8250_console_write`.
This means it potentially spins for 20 seconds *per character* written to the console. If this is used to write a long string, the delay would be unacceptable. But, wait, `serial8250_console_write` is called with interrupts *disabled*. `uart_port_lock_irqsave` disables them! This is a recipe for a soft lockup. The console flush kthread (`pr/legacy/17`) is the one thatβs going to trigger this.
So, if `pr/legacy/17` is the culprit, it can block other tasks that want to print, or just hold the console lock. `pr/legacy/17` holds `console_lock` and `console_srcu`. The `console_lock` is a semaphore, and `pr/legacy` is a kthread, which seems like a valid use. But wait, why is `cgroup_lock_and_drain_offline` blocked for 143 seconds? That's really weird.
`cgroup_lock_and_drain_offline` is waiting on `dsct->offline_waitq`. The offline waitq is woken up when a cgroup is offlined. So, something is blocking the cgroup offlining process. Itβs likely a workqueue item like `css_killed_work_fn`. We need to examine that function.
|
| 17/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Error:
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:offline_waitq SourceTreePrefix:]
Results: map[References:<nil> TruncatedOutput:false]
|
| 18/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 26242
output: 53
thoughts: 17
Thoughts: Here's my understanding of the thought process, summarized as you requested:
**Deconstructing `offline_waitq` in the `cgroup` Context**
Okay, so I'm thinking about this `offline_waitq` field. Right now, it's registering as part of the `struct cgroup`, which immediately puts it in a specific framework. This gives me a quick sense of its purpose β it's something that's integral to the core cgroup structure. It's not a standalone component but is deeply embedded. Given that knowledge, I'm already starting to think about its relationship to the broader cgroup hierarchy and the implications for resource management and isolation. I need to dig deeper into the actual usage within the `cgroup` codebase. I'm already expecting it to be related to either waiting for resources to be available or the offline status of a cgroup.
|
| 19/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:cgroup::offline_waitq SourceTreePrefix:]
Results: map[References:[map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:cgroup_lock_and_drain_offline SourceFile:kernel/cgroup/cgroup.c SourceLine:3271] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:cgroup_lock_and_drain_offline SourceFile:kernel/cgroup/cgroup.c SourceLine:3276] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:init_cgroup_housekeeping SourceFile:kernel/cgroup/cgroup.c SourceLine:2124] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:offline_css SourceFile:kernel/cgroup/cgroup.c SourceLine:5803]] TruncatedOutput:false]
|
| 20/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 26752
output: 36
thoughts: 10
Thoughts: Okay, let's dive into this. Here's how I'd approach summarizing the "thoughts" scenario, keeping in mind the expert user:
**Analyzing "offline_css"**
Alright, so the prompt is just "Let's look at `offline_css`." Fine. Immediately, my mind starts ticking. The phrase "offline_css" implies a very specific context, right? It immediately triggers questions in my brain, things like:
* **What's the framework or project context?** Is this a React application? A static site generator? A custom build process? This dictates the potential complexity. I need to understand the architectural setup to really grasp the implications.
* **What are we actually trying to achieve?** Are we aiming for performance optimization, a Progressive Web App (PWA) strategy, or perhaps broader offline capabilities for a web application? This will lead to a deeper understanding.
* **What are the potential technologies associated with the implementation?** I'm thinking Service Workers are probably involved, alongside possibly a templating engine or build system for offline assets. This determines whether it will be a straightforward implementation.
* **What are some of the known challenges in this context?** I'm immediately thinking of things like cache invalidation, dealing with updates, and perhaps edge cases with older browsers. This influences my line of thought.
So, while the prompt is simple, it's a jumping-off point. My first step is always to mentally reconstruct the larger project picture to fully understand what's being asked. It means I will need more context, and I'm ready to investigate. I'm already anticipating the specifics of this "offline_css" problem. The wheels are turning.
|
| 21/2 |
2026/07/21 00:37 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:offline_css]
Results: map[SourceCode:5787: /* if the CSS is online, invoke ->css_offline() on it and mark it offline */
5788: static void offline_css(struct cgroup_subsys_state *css)
5789: {
5790: struct cgroup_subsys *ss = css->ss;
5791:
5792: lockdep_assert_held(&cgroup_mutex);
5793:
5794: if (!css_is_online(css))
5795: return;
5796:
5797: if (ss->css_offline)
5798: ss->css_offline(css);
5799:
5800: css->flags &= ~CSS_ONLINE;
5801: RCU_INIT_POINTER(css->cgroup->subsys[ss->id], NULL);
5802:
5803: wake_up_all(&css->cgroup->offline_waitq);
5804: }
SourceFile:kernel/cgroup/cgroup.c]
|
| 22/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 27459
output: 49
thoughts: 293
Thoughts: **Analyzing a Potential Race Condition**
Okay, so I'm digging into this code and I've just seen that `offline_css` is being called while `cgroup_mutex` is held. That immediately sets off alarm bells. Now, let me think... doesn't `cgroup_lock_and_drain_offline` also hold `cgroup_mutex`? That's what I suspect, and that would be a serious problem. Let's double-check how `cgroup_lock_and_drain_offline` works.
Alright, here's the relevant snippet: it does indeed acquire `cgroup_mutex` with `cgroup_lock()`. And then, within a loop, while processing descendants, it does something interesting. It acquires the mutex, then *releases* `cgroup_mutex` *before* calling `schedule()`. That's the crux of it. It releases the lock, then potentially schedules and waits.
This means that while the function *started* with the mutex held, it *releases* it before potentially blocking. That's good, but it means that the lock is not necessarily held for the entire duration of the function call. Now I need to figure out who calls `offline_css` to ensure this is safe.
|
| 23/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:offline_css SourceTreePrefix:]
Results: map[References:[map[ReferenceKind:calls ReferencingEntityKind:function ReferencingEntityName:css_killed_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6084]] TruncatedOutput:false]
|
| 24/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 28145
output: 40
thoughts: 14
Thoughts: Okay, let's dive into this. Here's my take on those thoughts, as though they were my own:
**Analyzing the Function: `css_killed_work_fn`**
Alright, let's get into this `css_killed_work_fn`. Immediately, I'm thinking about the context it operates within. What's the surrounding code? What's the broader system architecture? Is this a CSS optimization tool, a rendering engine component, or something else entirely? The name itself suggests that CSS might be the trigger for this function being activated, and possibly that it means some work is being dropped. My first instinct is to understand the work that is being affected, and why it is being 'killed'. I need to consider all the reasons that a function could have 'killed' work - a rendering issue? A design flaw? An optimization?
I'm mentally running through possible scenarios. Is this related to cascading issues? Maybe specificity conflicts that result in certain styles being overridden and their associated work being deemed irrelevant? Is this function involved in lazy loading, and some work is being postponed or discarded due to viewport constraints or resource availability? I'm already formulating questions about the input parameters, the return value, and any side effects it might have. This needs to be a detailed investigation.
|
| 25/2 |
2026/07/21 00:37 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:css_killed_work_fn]
Results: map[SourceCode:6070: /*
6071: * This is called when the refcnt of a css is confirmed to be killed.
6072: * css_tryget_online() is now guaranteed to fail. Tell the subsystem to
6073: * initiate destruction and put the css ref from kill_css_finish().
6074: */
6075: static void css_killed_work_fn(struct work_struct *work)
6076: {
6077: struct cgroup_subsys_state *css;
6078:
6079: css = container_of(to_rcu_work(work), struct cgroup_subsys_state, destroy_rwork);
6080:
6081: cgroup_lock();
6082:
6083: do {
6084: offline_css(css);
6085: css_put(css);
6086: /* @css can't go away while we're holding cgroup_mutex */
6087: css = css->parent;
6088: } while (css && atomic_dec_and_test(&css->online_cnt));
6089:
6090: cgroup_unlock();
6091: }
SourceFile:kernel/cgroup/cgroup.c]
|
| 26/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 28835
output: 50
thoughts: 124
Thoughts: **Analyzing the Delay in css_killed_work_fn**
Okay, so `css_killed_work_fn` is a workqueue function. My initial thought is to trace the execution flow and identify potential bottlenecks. It acquires `cgroup_mutex`, calls `offline_css`, then releases the mutex. Standard stuff, but I need to understand potential contention points. The interesting part is that if `css_killed_work_fn` is delayed, `cgroup_lock_and_drain_offline` will be held up waiting on it. Hmm, why might this be delayed?
The fact that it's a workqueue function is the key. Workqueues are asynchronous, which means any delay in the workqueue execution will have a ripple effect. I need to pinpoint which workqueue is responsible. My hunch is to investigate the queuing mechanism. `destroy_rwork` is involved, and it is an `rcu_work`. This is getting interesting. Let me trace where `destroy_rwork` is enqueued, that should tell me where the delay originates.
|
| 27/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Error:
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:destroy_rwork SourceTreePrefix:]
Results: map[References:<nil> TruncatedOutput:false]
|
| 28/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 29256
output: 58
thoughts: 22
Thoughts: Here's my understanding of the thought process, summarized as you requested:
**Deconstructing `cgroup_subsys_state`**
Okay, so I'm looking at this code and trying to grasp a specific data structure. My immediate focus is on the `struct cgroup_subsys_state`. Ah, the lightbulb just went off - `destroy_rwork` is actually a *field* within that `struct cgroup_subsys_state`. That's important. Knowing it's a field immediately contextualizes it within the larger cgroup subsystem landscape and helps me to understand its function and purpose in relation to the state of a specific cgroup subsystem. Now I can start to reason about *why* that field exists, and how it is used.
|
| 29/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:cgroup_subsys_state::destroy_rwork SourceTreePrefix:]
Results: map[References:[map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5859] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5859] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5859] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5859] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5859] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_create SourceFile:kernel/cgroup/cgroup.c SourceLine:5860] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:css_free_rwork_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5597] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6100] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6100] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6100] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6100] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6100] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_killed_ref_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6101] map[ReferenceKind:reads ReferencingEntityKind:function ReferencingEntityName:css_killed_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:6079] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5709] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5709] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5709] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5709] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5709] map[ReferenceKind:takes-address-of ReferencingEntityKind:function ReferencingEntityName:css_release_work_fn SourceFile:kernel/cgroup/cgroup.c SourceLine:5710]] TruncatedOutput:false]
|
| 30/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 30647
output: 40
thoughts: 13
Thoughts: Okay, let's dive into this. Here's my take on those thoughts, as if they're my own:
**Analyzing `css_killed_ref_fn`**
Right, let's break this down. My initial reaction is to consider the implications of this function name, `css_killed_ref_fn`. The "css" suggests we're dealing with Cascading Style Sheets, obviously. "Killed" immediately raises a flag. Is this function about removing or overriding CSS rules? That's the most likely interpretation. And the "ref" or "ref_fn" part⦠that strongly implies it's related to some kind of reference or a function that handles CSS references.
Okay, now let's think about the context. This could be anything from a library function in a CSS-in-JS setup, a utility within a CSS preprocessor, or even a specialized function within a web framework. The crucial question is *how* it kills the reference. Does it completely remove a CSS rule, maybe from a linked stylesheet or a dynamically generated one? Does it "kill" it by applying an overriding style with a higher specificity? Or maybe it's more subtle, dealing with a reference to a CSS variable or a CSS module, and it's invalidating that link? We'll need more info to understand the *mechanism* of the "killing".
I need to consider the potential side effects, too. If this is removing a rule, what happens to elements that were relying on it? If it's overriding, are we respecting the cascade correctly? Is there a performance hit associated with this operation? Is it using important? What is the scope of its operation. I'd need to consider how this would affect accessibility, performance, and overall maintainability of the codebase. I'm going to have to dig deeper, to see the surrounding code, to really see what we are doing here.
|
| 31/2 |
2026/07/21 00:37 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:css_killed_ref_fn]
Results: map[SourceCode:6093: /* css kill confirmation processing requires process context, bounce */
6094: static void css_killed_ref_fn(struct percpu_ref *ref)
6095: {
6096: struct cgroup_subsys_state *css =
6097: container_of(ref, struct cgroup_subsys_state, refcnt);
6098:
6099: if (atomic_dec_and_test(&css->online_cnt)) {
6100: INIT_RCU_WORK(&css->destroy_rwork, css_killed_work_fn);
6101: queue_rcu_work(cgroup_offline_wq, &css->destroy_rwork);
6102: }
6103: }
SourceFile:kernel/cgroup/cgroup.c]
|
| 32/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 31334
output: 53
thoughts: 946
Thoughts: **Analyzing a Potential Soft Lockup: The Console Conundrum**
Okay, so I'm looking at this stack trace and it looks like a hung task. It's all starting in the `cgroup_offline_wq`. I wonder if that workqueue is blocked? It's a workqueue, so it's susceptible to CPU contention. Ah, wait, if there's a soft lockup on CPU 1, and CPU 0 is also busy with `khungtaskd`, then that workqueue can't run.
Let me see. CPU 1 is stuck in `io_serial_in` - a soft lockup. And CPU 0 is running `khungtaskd`, printing that hung task warning. Okay, CPU 1 is stuck within `serial8250_console_write`. That means itβs holding `console_lock` and the `port_lock_key`. And it's spinning with interrupts disabled. Ah ha! `uart_port_lock_irqsave` disables interrupts. So CPU 1 is completely unresponsive, it's a dead lock.
If CPU 1 is unresponsive, RCU grace periods cannot complete! `queue_rcu_work` waits for an RCU grace period before queuing the work to the actual workqueue. If CPU 1 is stuck with interrupts disabled, RCU grace periods will stall. Therefore, `css_killed_work_fn` will never be executed, because the RCU grace period never completes. So `cgroup_lock_and_drain_offline` will wait forever, explaining the hung task.
So the soft lockup in `serial8250_console_write` on CPU 1 is the root cause. Now, *why* is `serial8250_console_write` stuck? Because `wait_for_lsr` is spinning for a very long time. And why is `wait_for_lsr` spinning? Because `tmout` is very large! And why is `tmout` large? `up->port.frame_time` is huge! And why is *that* huge? Because the baud rate was set to a very small value, like 1 or 0.
Wait, can a *user* set the baud rate of the serial console? Yes, via `ioctl(TIOCSSERIAL)` or `ioctl(TCSETS)` on the serial port! So, if an unprivileged user can open the serial port and change its baud rate, they could cause a soft lockup and a denial of service!
Let's check the permissions on the serial console device node. Usually, `/dev/console` or `/dev/ttyS0` is owned by root and has permissions `crw-------` or `crw--w----` (root:tty). So an unprivileged user can't open it.
Wait, what about a pseudo-terminal or another serial port? If they open a USB serial port and set the baud rate to 1, and then something prints to it? But the stack trace shows `serial8250_console_write`, which is the console write function.
So can a user change the baud rate of the *serial console*? Only if they have access to the device node. Wait, syzkaller runs as root in its test environment, or uses user namespaces. If it has CAP_SYS_ADMIN, it still can't access `/dev/ttyS0` unless bind-mounted or if it's created. What about creating a virtual device? No, the console is usually set via the kernel command line.
What if the user uses `TIOCSSERIAL` on a pty? That doesn't affect `8250_port`. Okay, `TIOCSSERIAL` on `/dev/ttyS0`? Syzkaller often has access because it runs as root or is made accessible for testing. But in a real system, `/dev/ttyS0` is restricted to root. Let's see if there is any other way `frame_time` could be huge. Let me look at `uart_update_timeout`.
|
| 33/2 |
2026/07/21 00:37 |
tool |
codesearch-find-references |
0m
Args: map[ContextFile:drivers/tty/serial/serial_core.c IncludeSnippetLines:0 Name:uart_update_timeout SourceTreePrefix:]
Results: map[References:[map[ReferenceKind:calls ReferencingEntityKind:function ReferencingEntityName:serial8250_do_set_termios SourceFile:drivers/tty/serial/8250/8250_port.c SourceLine:2801] map[ReferenceKind:takes-address-of ReferencingEntityKind:global_variable ReferencingEntityName:__UNIQUE_ID_addressable_uart_update_timeout_998 SourceFile:drivers/tty/serial/serial_core.c SourceLine:453] map[ReferenceKind:takes-address-of ReferencingEntityKind:global_variable ReferencingEntityName:__gendwarfksyms_ptr_uart_update_timeout SourceFile:drivers/tty/serial/serial_core.c SourceLine:453] map[ReferenceKind:takes-address-of ReferencingEntityKind:global_variable ReferencingEntityName:__gendwarfksyms_ptr_uart_update_timeout SourceFile:drivers/tty/serial/serial_core.c SourceLine:453]] TruncatedOutput:false]
|
| 34/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 33511
output: 55
thoughts: 44
Thoughts: Here's my thought process, as if I were analyzing this code:
**Diving into Serial Driver Configuration**
Okay, so I see that `serial8250_do_set_termios` is calling `uart_update_timeout`. Immediately, that tells me something important about how the 8250 serial driver handles timeout settings β they're updated within the `set_termios` function. Good to know. Let's dig into `serial8250_do_set_termios` itself and see exactly how those timeouts are being calculated and configured. I suspect we'll find the baud rate, character size, parity, and stop bits are all playing a role, of course, and I'll want to see how those are being translated to the underlying hardware registers. I'll need to confirm if it's updating the timeout values directly, or if it has any conditional logic based on specific terminal configurations. Let's see how they've handled this...
|
| 35/2 |
2026/07/21 00:37 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:serial8250_do_set_termios]
Results: map[SourceCode:2777: void
2778: serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
2779: const struct ktermios *old)
2780: {
2781: struct uart_8250_port *up = up_to_u8250p(port);
2782: unsigned int baud, quot, frac = 0;
2783: u8 lcr;
2784:
2785: serial8250_set_mini(port, termios);
2786: lcr = serial8250_compute_lcr(up, termios->c_cflag);
2787: baud = serial8250_get_baud_rate(port, termios, old);
2788: quot = serial8250_get_divisor(port, baud, &frac);
2789:
2790: /*
2791: * Ok, we're now changing the port state. Do it with interrupts disabled.
2792: *
2793: * Synchronize UART_IER access against the console.
2794: */
2795: scoped_guard(serial8250_rpm, up) {
2796: guard(uart_port_lock_irqsave)(port);
2797:
2798: up->lcr = lcr;
2799: serial8250_set_trigger_for_slow_speed(port, termios, baud);
2800: serial8250_set_afe(port, termios);
2801: uart_update_timeout(port, termios->c_cflag, baud);
2802: serial8250_set_errors_and_ignores(port, termios);
2803: serial8250_set_ier(port, termios);
2804: serial8250_set_efr(port, termios);
2805: serial8250_set_divisor(port, baud, quot, frac);
2806: serial8250_set_fcr(port, termios);
2807: /* Consoles manually poll CTS for hardware flow control. */
2808: if (uart_console(port) &&
2809: !(port->rs485.flags & SER_RS485_ENABLED)
2810: && termios->c_cflag & CRTSCTS) {
2811: port->mctrl |= TIOCM_RTS;
2812: }
2813: serial8250_set_mctrl(port, port->mctrl);
2814: }
2815:
2816: /* Don't rewrite B0 */
2817: if (tty_termios_baud_rate(termios))
2818: tty_termios_encode_baud_rate(termios, baud, baud);
2819: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 36/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 34659
output: 54
thoughts: 41
Thoughts: Okay, here's my interpretation of that thought process, assuming I'm deep in the weeds of embedded systems programming:
**Examining the Baud Rate Acquisition**
Right, let's start with this line: `baud = serial8250_get_baud_rate(port, termios, old);`. Immediately, my brain zeroes in on `serial8250_get_baud_rate`. That's the function responsible for determining the serial communication speed, or baud rate, for an 8250 UART. I need to understand exactly how that's working within the context of this `port`, `termios`, and `old` configuration. I see that this function is how the baud rate is being calculated. I'll need to know this value.
I wonder where the specific parameters come from.
|
| 37/2 |
2026/07/21 00:37 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:serial8250_get_baud_rate]
Results: map[SourceCode:2569: static unsigned int serial8250_get_baud_rate(struct uart_port *port,
2570: struct ktermios *termios,
2571: const struct ktermios *old)
2572: {
2573: unsigned int tolerance = port->uartclk / 100;
2574: unsigned int min;
2575: unsigned int max;
2576:
2577: /*
2578: * Handle magic divisors for baud rates above baud_base on SMSC
2579: * Super I/O chips. Enable custom rates of clk/4 and clk/8, but
2580: * disable divisor values beyond 32767, which are unavailable.
2581: */
2582: if (port->flags & UPF_MAGIC_MULTIPLIER) {
2583: min = port->uartclk / 16 / UART_DIV_MAX >> 1;
2584: max = (port->uartclk + tolerance) / 4;
2585: } else {
2586: min = port->uartclk / 16 / UART_DIV_MAX;
2587: max = (port->uartclk + tolerance) / 16;
2588: }
2589:
2590: /*
2591: * Ask the core to calculate the divisor for us.
2592: * Allow 1% tolerance at the upper limit so uart clks marginally
2593: * slower than nominal still match standard baud rates without
2594: * causing transmission errors.
2595: */
2596: return uart_get_baud_rate(port, termios, old, min, max);
2597: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 38/2 |
2026/07/21 00:37 |
llm |
expert |
0m
Model:
Tokens:
input: 35442
output: 52
thoughts: 909
Thoughts: **Analyzing a Potential Soft Lockup in Serial Console Output**
Okay, so I'm digging into a potential soft lockup issue related to serial console output, specifically focusing on how an unprivileged user might trigger it. The core of the problem seems to be linked to the `uart_get_baud_rate` function. If the minimum calculated baud rate (`min`) is zero, or a very low value, `uart_get_baud_rate` can return 0. The maximum divisor is `0xffff` (65535). So, if my serial port clock (`port->uartclk`) is, say, the standard 1843200 Hz for 115200 baud, then the calculation gives me `min = 1843200 / 16 / 65535 = 1`.
Now, if `baud` is 1, the `frame_time` becomes ridiculously long: `10 * 10^9 / 1 = 10^10` ns, which equals 10 seconds per byte. This cascades into `wait_for_lsr` having a huge timeout, roughly 20 seconds. Since `wait_for_lsr` uses a `udelay(1)` loop, the serial driver would wait for 20 seconds for each character. Printing a 100-character string would take a whopping 2000 seconds (over half an hour), and in the meantime, the CPU is disabled. If this happens while a critical task runs with interrupts disabled, this could definitely trigger a soft lockup, because serial8250_console_write runs with interrupts disabled.
The question then is, how *can* an unprivileged user set the baud rate to such a low value? I know that changing the baud rate of the serial console requires an `ioctl(TCSETS)` call on the serial device node like `/dev/ttyS0`. However, the permissions on these devices are typically restrictive, like `crw-rw----` or `crw--w----`, owned by `root:dialout` or `root:tty`, so generally, unless they are in the dialout group, a user won't have the necessary access to manipulate it.
What about a pseudo-terminal (pty)? Thankfully, ptys don't use `8250_port.c` which I am focusing on here, but `pty.c`, so I don't need to consider that. USB serial devices? USB serial adapters usually use `drivers/usb/serial/`, not this.
The more interesting angle is if an unprivileged user could trigger kernel prints while the console is in this slow mode. Root or a system administrator *could* set the console to 1 baud, and then the system would hang on any printk. That's a deliberate action by a privileged user, though. But what if they could trigger a lot of kernel printks? Even at normal baud rates, printing a massive amount of data to the serial console can cause soft lockups, a well-known problem. So, if they could somehow trigger many warnings, or write to `/dev/kmsg` if that's accessible, or cause some rate-limited network messages, they might be able to create the soft lockup.
I've also seen in the bug report that `pr/legacy/17` is stuck in `io_serial_in`. Ah, `pr/legacy` is a kernel thread responsible for flushing the printk buffer to legacy consoles. This thread was introduced in the threaded printk implementation. If it's flushing the console, it holds `console_lock` and `console_srcu`.
The crucial bit, though, is that `pr/legacy` *doesn't* disable interrupts for the entire flush, only inside `serial8250_console_write`. Let's dig deeper into the code of `serial8250_console_write` to understand exactly what's going on within.
|
| 39/2 |
2026/07/21 00:38 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:serial8250_console_write]
Results: map[SourceCode:3321: /*
3322: * Print a string to the serial port trying not to disturb
3323: * any possible real use of the port...
3324: *
3325: * The console_lock must be held when we get here.
3326: *
3327: * Doing runtime PM is really a bad idea for the kernel console.
3328: * Thus, we assume the function is called when device is powered up.
3329: */
3330: void serial8250_console_write(struct uart_8250_port *up, const char *s,
3331: unsigned int count)
3332: {
3333: struct uart_8250_em485 *em485 = up->em485;
3334: struct uart_port *port = &up->port;
3335: unsigned long flags;
3336: unsigned int ier, use_fifo;
3337: int locked = 1;
3338:
3339: touch_nmi_watchdog();
3340:
3341: if (oops_in_progress)
3342: locked = uart_port_trylock_irqsave(port, &flags);
3343: else
3344: uart_port_lock_irqsave(port, &flags);
3345:
3346: /*
3347: * First save the IER then disable the interrupts
3348: */
3349: ier = serial_port_in(port, UART_IER);
3350: serial8250_clear_IER(up);
3351:
3352: /* check scratch reg to see if port powered off during system sleep */
3353: if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
3354: serial8250_console_restore(up);
3355: up->canary = 0;
3356: }
3357:
3358: if (em485) {
3359: if (em485->tx_stopped)
3360: up->rs485_start_tx(up, false);
3361: mdelay(port->rs485.delay_rts_before_send);
3362: }
3363:
3364: use_fifo = (up->capabilities & UART_CAP_FIFO) &&
3365: /*
3366: * BCM283x requires to check the fifo
3367: * after each byte.
3368: */
3369: !(up->capabilities & UART_CAP_MINI) &&
3370: /*
3371: * tx_loadsz contains the transmit fifo size
3372: */
3373: up->tx_loadsz > 1 &&
3374: (up->fcr & UART_FCR_ENABLE_FIFO) &&
3375: port->state &&
3376: test_bit(TTY_PORT_INITIALIZED, &port->state->port.iflags) &&
3377: /*
3378: * After we put a data in the fifo, the controller will send
3379: * it regardless of the CTS state. Therefore, only use fifo
3380: * if we don't use control flow.
3381: */
3382: !uart_console_hwflow_active(&up->port);
3383:
3384: if (likely(use_fifo))
3385: serial8250_console_fifo_write(up, s, count);
3386: else
3387: uart_console_write(port, s, count, serial8250_console_wait_putchar);
3388:
3389: /*
3390: * Finally, wait for transmitter to become empty
3391: * and restore the IER
3392: */
3393: wait_for_xmitr(up, UART_LSR_BOTH_EMPTY);
3394:
3395: if (em485) {
3396: mdelay(port->rs485.delay_rts_after_send);
3397: if (em485->tx_stopped)
3398: up->rs485_stop_tx(up, false);
3399: }
3400:
3401: serial_port_out(port, UART_IER, ier);
3402:
3403: /*
3404: * The receive handling will happen properly because the
3405: * receive ready bit will still be set; it is not cleared
3406: * on read. However, modem control will not, we must
3407: * call it if we have saved something in the saved flags
3408: * while processing with interrupts off.
3409: */
3410: if (up->msr_saved_flags)
3411: serial8250_modem_status(up);
3412:
3413: if (locked)
3414: uart_port_unlock_irqrestore(port, flags);
3415: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 40/2 |
2026/07/21 00:38 |
llm |
expert |
0m
Model:
Tokens:
input: 38764
output: 37
thoughts: 1292
Thoughts: **Analyzing a Potential Soft Lockup in the Serial Console Driver**
Okay, so I'm looking at this `serial8250_console_write` function. My initial thought is that it's disabling interrupts with `uart_port_lock_irqsave`, writing a string, and then re-enabling interrupts. If the string is long or the serial port is slow, that could potentially be a problem because interrupts are disabled for a relatively long time. But wait, `console_flush_one_record` handles flushing things a record at a time, each record maxes at 1024 bytes, and at 115200 baud, 1024 bytes takes about 100ms. That's a noticeable interrupt disable time, but it won't cause the reported 143-second hang.
The bug report mentions a hung task, not a soft lockup. That's a crucial distinction. But, wait... the NMI backtrace says `Tainted: [L]=SOFTLOCKUP`. Okay, there *is* a soft lockup! CPU 1 is soft-locked up in `io_serial_in`. That's the real problem. Why would `io_serial_in` take so long? It's likely `wait_for_lsr` is spinning. Why would `wait_for_lsr` spin for a long time? Because the timeout (`tmout`) is huge, or the hardware isn't setting the Line Status Register (LSR) bit. If the hardware isn't setting the LSR bit, `wait_for_lsr` will spin until the timeout, which is likely calculated based on baud rate. If the baud rate is 1, a single character will spin for a very long time! A `tmout` of 20,000,000 will be 20 seconds, so writing 1000 characters would lock up for 20,000 seconds.
So, how did the baud rate get set to 1? Is there a Syzkaller program that sets the baud rate to 1? Syzkaller can open `/dev/ttyS0` if permissions allow, or it can use `TIOCSSERIAL`. Syzkaller tests run as root in a user namespace with `sandbox = namespace`, so it can't directly open `/dev/ttyS0` because it's not owned by the user. But Syzkaller has a virtual device, `syz_usb_connect` that creates a USB serial device. But, that uses a different driver, not `8250`. Wait, what about `serial8250_console_write`? It's the console! If Syzkaller can trigger a soft lockup by setting the baud rate of `/dev/ttyS0` to 1, it has root access to `/dev/ttyS0`. But it's not a security vulnerability as root is already privileged.
Could an unprivileged user do this? No, an unprivileged user can't open `/dev/ttyS0`. What about using `TIOCSSERIAL` on a pty? No, ptys have their own tty operations. What about a ton of printks? If an unprivileged user can trigger a lot of printks, and the console is at 115200 baud, could it cause a soft lockup? At 115200 baud, a 1024 byte printk takes ~90ms. `serial8250_console_write` writes the whole record with interrupts disabled, and `pr/legacy` kthread flushes the records:
```c
while (console_flush_one_record(...))
cond_resched();
```
`console_flush_one_record` *doesn't* release the console lock - `pr/legacy` holds it. So, a massive flood of printks could indeed cause a soft lockup, but the baud rate of the console needs to be low to trigger it.
|
| 41/2 |
2026/07/21 00:38 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/printk/printk.c Name:legacy_kthread_func]
Results: map[SourceCode:3704: static int legacy_kthread_func(void *unused)
3705: {
3706: bool try_again;
3707:
3708: wait_for_event:
3709: wait_event_interruptible(legacy_wait, legacy_kthread_should_wakeup());
3710:
3711: do {
3712: bool handover = false;
3713: u64 next_seq = 0;
3714:
3715: if (kthread_should_stop())
3716: return 0;
3717:
3718: console_lock();
3719: console_flush_one_record(true, &next_seq, &handover, &try_again);
3720: if (!handover)
3721: __console_unlock();
3722:
3723: } while (try_again);
3724:
3725: goto wait_for_event;
3726: }
SourceFile:kernel/printk/printk.c]
|
| 42/2 |
2026/07/21 00:38 |
llm |
expert |
0m
Model:
Tokens:
input: 41286
output: 39
thoughts: 238
Thoughts: **Analyzing the Console Logging Path**
Okay, so I'm looking at this `legacy_kthread_func` function and seeing how it handles console output. It looks like it grabs the `console_lock()` before each record, then calls `console_flush_one_record` to actually write the data, and then releases the lock immediately with `__console_unlock()`. The key thing here is that the lock is released after *every* record, not held for the entire loop.
My initial thought was that with 90ms per record with interrupts disabled, that it might be an issue. But the interrupts are only disabled inside `serial8250_console_write`. And if the system takes 90ms for each record, then it's only 90ms of uninterupted execution. This should be fine, and not cause a soft lockup, since it requires 20 seconds.
But now I see `serial8250_console_write` calls `touch_nmi_watchdog()`. And that's not all, `wait_for_lsr` calls it too. Ah, that's interesting. `touch_nmi_watchdog()` should reset the soft lockup watchdog! Wait a minute, I think it resets the NMI watchdog, the hard lockup detector, but does it do anything for the soft lockup detector? I need to check the definition of `touch_nmi_watchdog` to be sure. I'll check it, because if it resets the soft lockup detector, the 90ms should be fine.
|
| 43/2 |
2026/07/21 00:38 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:include/linux/nmi.h Name:touch_nmi_watchdog]
Results: map[SourceCode: 130: /**
131: * touch_nmi_watchdog - manually reset the hardlockup watchdog timeout.
132: *
133: * If we support detecting hardlockups, touch_nmi_watchdog() may be
134: * used to pet the watchdog (reset the timeout) - for code which
135: * intentionally disables interrupts for a long time. This call is stateless.
136: *
137: * Though this function has "nmi" in the name, the hardlockup watchdog might
138: * not be backed by NMIs. This function will likely be renamed to
139: * touch_hardlockup_watchdog() in the future.
140: */
141: static inline void touch_nmi_watchdog(void)
142: {
143: /*
144: * Pass on to the hardlockup detector selected via CONFIG_. Note that
145: * the hardlockup detector may not be arch-specific nor using NMIs
146: * and the arch_touch_nmi_watchdog() function will likely be renamed
147: * in the future.
148: */
149: arch_touch_nmi_watchdog();
150:
151: touch_softlockup_watchdog();
152: }
SourceFile:include/linux/nmi.h]
|
| 44/2 |
2026/07/21 00:38 |
llm |
expert |
0m
Model:
Tokens:
input: 42304
output: 39
thoughts: 737
Thoughts: **Decoding a Kernel Hang: A Multi-Layered Mystery**
Okay, let's break this down. First, `touch_nmi_watchdog()` calls `touch_softlockup_watchdog()`. That means `wait_for_lsr` is indeed resetting the soft lockup watchdog every time it spins. But... we got a soft lockup. How? The NMI backtrace showed a `Tainted: [L]=SOFTLOCKUP`, and the soft lockup was on CPU 1. However, the initial bug report highlighted a *hung task* β specifically, `syz.4.1502:10156` blocked for over 143 seconds. That's a D-state, hung task. The hung task detector fired.
Now, the hung task detector triggers a stack trace of the blocked task and *can* initiate an NMI backtrace on all CPUs. But wait, `check_hung_uninterruptible_tasks` calls `trigger_all_cpu_backtrace`. The NMI backtrace is simply a snapshot of what *each* CPU was doing when the hung task detector ran! It's *not* the soft lockup detector. The `Tainted: [L]=SOFTLOCKUP` entry on the backtrace tells me the kernel was *previously* tainted due to a soft lockup! So, a soft lockup *did* happen earlier, but the current problem is a *hung task*.
So, why is the task hung? The trace points to `cgroup_lock_and_drain_offline` waiting for `offline_waitq`. It's blocked because `css_killed_work_fn` isn't executing. Why? Because it's queued on `cgroup_offline_wq`, which is a workqueue. Okay, is the workqueue blocked? Let's see... looking at the worker threads, we have a bunch of kworkers running various tasks: `process_one_work`, `hub_event`, `bat_events`, `nsim_dev_trap_report_work`, and `kfence_timer` across several CPUs.
Wait a second, `cgroup_offline_wq` is a *normal* workqueue. Could it be that *all* the worker threads in its pool are busy? If they're all blocked on something else, the queue won't be able to execute new work! Aha, wait, `cgroup_offline_wq` was created as `alloc_workqueue("cgroup_offline", WQ_UNBOUND, 1);`. `WQ_UNBOUND` with `max_active = 1`? I need to double-check that... something seems off here...
|
| 45/2 |
2026/07/21 00:38 |
tool |
codesearch-definition-source |
0m
Error:
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:cgroup_offline_wq]
Results: map[SourceCode: SourceFile:]
|
| 46/2 |
2026/07/21 00:38 |
llm |
expert |
0m
Model:
Tokens:
input: 43682
output: 31
thoughts: 13
Thoughts: Here's my thought process, as if I were considering this search:
**Investigating `cgroup_offline_wq`**
Okay, let's dive into this. The presence of `cgroup_offline_wq` immediately suggests we're dealing with the cgroup subsystem and some kind of workqueue related to it. My initial thought is to figure out the context. Is this a performance issue, a bug report, or am I just brushing up on internal workings? I need to understand why I'm looking for this now. What triggered this query?
I'm assuming this workqueue relates to offlining a cgroup, which, from experience, usually involves moving processes, releasing resources, and generally cleaning up. If I remember correctly, there could be complexities related to how this works with nested cgroups, resource exhaustion, or interactions with other kernel subsystems like memory management or the scheduler.
I'm thinking I'll start by searching the kernel source code, specifically looking for definitions, uses, and any relevant commit messages. Looking at the call sites would be key to figure out how `cgroup_offline_wq` fits into the broader picture. I need to understand its role and what might be going wrong in a particular scenario. I'm also planning to check if there are any known issues or discussions related to this workqueue in mailing lists or bug trackers. Understanding the control flow around it is paramount. I'm probably going to have to trace a sequence of function calls to grasp the whole picture. I'll need to figure out where the workqueue is created, how tasks are submitted, and what operations are performed when a task runs. I'm also going to see if any lock contention or potential race conditions come up.
|
| 47/2 |
2026/07/21 00:38 |
tool |
grepper |
0m
Args: map[Expression:cgroup_offline_wq PathPrefix:kernel/cgroup/]
Results: map[Output:kernel/cgroup/cgroup.c=102=DEFINE_PERCPU_RWSEM(cgroup_threadgroup_rwsem);
--
kernel/cgroup/cgroup.c-115- * A cgroup destruction should enqueue work sequentially to:
kernel/cgroup/cgroup.c:116: * cgroup_offline_wq: use for css offline work
kernel/cgroup/cgroup.c-117- * cgroup_release_wq: use for css release work
--
kernel/cgroup/cgroup.c-135- */
kernel/cgroup/cgroup.c:136:static struct workqueue_struct *cgroup_offline_wq;
kernel/cgroup/cgroup.c-137-static struct workqueue_struct *cgroup_release_wq;
--
kernel/cgroup/cgroup.c=779=static void css_update_populated(struct cgroup_subsys_state *css, bool populated)
--
kernel/cgroup/cgroup.c-822- css_get(css);
kernel/cgroup/cgroup.c:823: WARN_ON_ONCE(!queue_work(cgroup_offline_wq, &css->kill_finish_work));
kernel/cgroup/cgroup.c-824- }
--
kernel/cgroup/cgroup.c=6094=static void css_killed_ref_fn(struct percpu_ref *ref)
--
kernel/cgroup/cgroup.c-6100- INIT_RCU_WORK(&css->destroy_rwork, css_killed_work_fn);
kernel/cgroup/cgroup.c:6101: queue_rcu_work(cgroup_offline_wq, &css->destroy_rwork);
kernel/cgroup/cgroup.c-6102- }
--
kernel/cgroup/cgroup.c=6525=static int __init cgroup_wq_init(void)
--
kernel/cgroup/cgroup.c-6534- */
kernel/cgroup/cgroup.c:6535: cgroup_offline_wq = alloc_workqueue("cgroup_offline", WQ_PERCPU, 1);
kernel/cgroup/cgroup.c:6536: BUG_ON(!cgroup_offline_wq);
kernel/cgroup/cgroup.c-6537-
]
|
| 48/2 |
2026/07/21 00:38 |
llm |
expert |
0m
Model:
Tokens:
input: 44688
output: 38
thoughts: 1905
Thoughts: **Root Cause Analysis of cgroup_lock_and_drain_offline Hang**
Okay, so I'm looking at this hang in `cgroup_lock_and_drain_offline`. It's pretty clear that it's related to the `cgroup_offline_wq` workqueue, and specifically the interaction with RCU. Initially, I thought that `WQ_PERCPU` was some flag I didn't recognize, but no, it's either a macro or simply zero, and that's fine. The key is that `max_active` is 1, meaning only one work item can run per CPU. If that item blocks, the whole CPU's workqueue is blocked. I checked, and the workers aren't holding any locks that would explain the hold up.
I see that `queue_rcu_work` is involved, and that's where things get interesting. The work gets queued to `rcu_work` and *then* after an RCU grace period, it's queued to `cgroup_offline_wq`. If the grace period never completes, the work is never run. I started wondering *why* the grace period might not complete.
And I realized it's because a CPU can get stuck in an RCU read-side critical section or when interrupts are disabled. Looking at the stack trace, CPU 1 is the culprit. It's running `pr/legacy` and stuck in `io_serial_in`. This leads to `wait_for_lsr` which is from `serial8250_console_write`. And *that* disables interrupts! So, CPU 1 has interrupts disabled, which is preventing scheduling and blocking the RCU grace period. Although, `touch_nmi_watchdog` is called, but it does not enable interrupts.
So, CPU 1 is spinning with interrupts disabled, which blocks RCU grace periods and results in `css_killed_work_fn` not being called. This, in turn, blocks `offline_waitq`, and voila, `cgroup_lock_and_drain_offline` hangs for a long time - 143 seconds in this case. The hung task detector fires. It all links together perfectly.
The fundamental issue is that `serial8250_console_write` spins with interrupts disabled. Now the question is why is it spinning for a very long time? It's because `wait_for_lsr` is spinning for a long time. It can be due to a large `tmout` value, or writing a lot of characters that takes time.
If the baud rate is normal, `tmout` is small, but if writing a lot of characters, it can still take a long time, but one record which is 1024 bytes and normal baud rate shouldn't be long enough. To trigger a 143 second hang, it means the `serial8250_console_write` must take 143 seconds, only if the baud rate is very low. At a baud rate of 1, each character will take 10 seconds. In this case, the baud rate MUST be set to a very low value.
Now, an unprivileged user can't change the baud rate (they can't open `/dev/ttyS0`). But wait, what if the console is a virtual console? No, the stack trace points to the serial driver. What about syzkaller? Syzkaller runs as root in the test environment, so it can change the baud rate. If root sets a very low baud rate, it creates a denial of service. The question then is, is this a security bug? Usually, it's allowed for root to change the serial console baud rate - a known limitation, not a bug, since root is already privileged.
Could there be other ways to trigger this? A faulty hardware device or a malicious USB device that emulates a serial port and never sets the LSR bit? If that happened, `wait_for_lsr` would spin until `tmout` reaches zero. Even with a malicious device, it's not possible to have a 143-second hang, unless the baud rate is also set to a very low value.
Could `up->port.frame_time` be zero? If `frame_time` is zero, `tmout` would be 10000. That's 10ms per character, leading to 10 seconds to write 1024 characters. Still not 143 seconds. The only way to get this long hang is with a very large `frame_time`, which occurs only when the baud rate is very low, which is only set by root, or someone with access to
|
| 49/2 |
2026/07/21 00:39 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/watchdog.c Name:touch_softlockup_watchdog]
Results: map[SourceCode: 709: notrace void touch_softlockup_watchdog(void)
710: {
711: touch_softlockup_watchdog_sched();
712: wq_watchdog_touch(raw_smp_processor_id());
713: }
SourceFile:kernel/watchdog.c]
|
| 50/2 |
2026/07/21 00:39 |
llm |
expert |
0m
Model:
Tokens:
input: 47763
output: 40
thoughts: 16
Thoughts: Okay, here's my attempt at summarizing that thought process, keeping in mind I'm speaking to a fellow expert:
**Investigating `touch_softlockup_watchdog_sched`**
Alright, time to dive into this. The context, of course, isn't explicitly stated here, but based on the name, my mind immediately jumps to that kernel function: `touch_softlockup_watchdog_sched`. Right off the bat, I'm thinking about the soft lockup watchdog mechanism, scheduler interactions, and potential implications for system responsiveness and detection. I need to refresh my understanding of how this specific function fits into the overall watchdog framework and what its role is in preventing or handling soft lockups related to scheduling anomalies. This could be related to priority inversion, lock contention within the scheduler, or some other scheduling edge case. My aim is to quickly understand *why* we're focusing on this particular function at this moment. Are we troubleshooting a reported issue, reviewing code, or prepping for a change? Knowing that will provide much needed context, otherwise, I will just dive in.
|
| 51/2 |
2026/07/21 00:39 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/watchdog.c Name:touch_softlockup_watchdog_sched]
Results: map[SourceCode: 692: /**
693: * touch_softlockup_watchdog_sched - touch watchdog on scheduler stalls
694: *
695: * Call when the scheduler may have stalled for legitimate reasons
696: * preventing the watchdog task from executing - e.g. the scheduler
697: * entering idle state. This should only be used for scheduler events.
698: * Use touch_softlockup_watchdog() for everything else.
699: */
700: notrace void touch_softlockup_watchdog_sched(void)
701: {
702: /*
703: * Preemption can be enabled. It doesn't matter which CPU's watchdog
704: * report period gets restarted here, so use the raw_ operation.
705: */
706: raw_cpu_write(watchdog_report_ts, SOFTLOCKUP_DELAY_REPORT);
707: }
SourceFile:kernel/watchdog.c]
|
| 52/2 |
2026/07/21 00:39 |
llm |
expert |
0m
Model:
Tokens:
input: 48337
output: 35
thoughts: 2134
Thoughts: **Analyzing a Soft Lockup and Hung Task**
Okay, so `touch_softlockup_watchdog_sched` resets the soft lockup timer β that much is clear. If `wait_for_lsr` is spinning and calling `touch_nmi_watchdog()`, then the soft lockup won't fire on CPU 1, which makes sense. But the kernel is tainted with `[L]=SOFTLOCKUP`, which raises a flag. If CPU 1 *isn't* the problem, it suggests another CPU. CPU 0 is running `khungtaskd`, but that shouldn't cause this issue.
Now, here's the kicker: if CPU 1 has interrupts disabled, it can't handle IPIs. If CPU 0 tries to send an IPI to CPU 1, it will spin, waiting for acknowledgment. Consequently, CPU 0 won't call `touch_nmi_watchdog()` either, leading to *its* soft lockup. So, let's see if CPU 0 is holding any locks that would indicate it was spinning on an IPI.
The bug report shows `rcu_read_lock` held by `khungtaskd`. This is from the hung task detector, no concern. But what about the other tasks? I see a variety of locks held, including `tty->ldisc_sem`, various mutexes, and locks related to USB and kernfs. None of these immediately scream "IPI spin."
But then the kernel being tainted has to be considered. The soft lockup could have occurred on any CPU at any time, leaving the taint. So we need to focus on why a hung task is *currently* happening.
The problem seems to be `cgroup_lock_and_drain_offline` waiting for `offline_waitq`. The work associated with `offline_waitq` is `css_killed_work_fn`. If `css_killed_work_fn` isn't running, `offline_waitq` will never be woken up. Is it being blocked?
It appears that `cgroup_offline_wq` has `max_active = 1`. Is there currently a work item on that queue? No, there is no work item running on that queue. Okay, but if `css_killed_work_fn` *were* running, it would be holding `cgroup_mutex`. `cgroup_lock_and_drain_offline` releases this mutex before sleeping, so that's not the issue. The critical point is: if the function were running, it would have acquired `cgroup_mutex`, called `offline_css`, and woken the wait queue. Because this hasn't happened, `css_killed_work_fn` is either not running or blocked on something.
The next step is to examine locks to see whether anyone has a hold on `cgroup_mutex`. `cgroup_mutex` is not listed as held. It *should* be free, and `css_killed_work_fn` should be able to acquire it, but it isn't running. Therefore, it hasn't been queued to `cgroup_offline_wq` yet! And `queue_rcu_work` is still waiting for an RCU grace period!
This is where the root cause emerges: CPU 1 is stuck in `serial8250_console_write` with interrupts disabled. It can't report a quiescent state to RCU. Thus, the RCU grace period never finishes, and `queue_rcu_work` doesn't enqueue `css_killed_work_fn`. `offline_waitq` is never woken up, and `cgroup_lock_and_drain_offline` hangs.
This confirms the chain. So, why is CPU 1 in this situation? Is it just printing too much to the serial console? Or, perhaps, a very low baud rate? The important part is: is this a security risk? An unprivileged user could be able to trigger this and cause a denial of service. The user can trigger many printks, and then, a lot of data is being written to the console.
But does `pr/legacy` continuously disable interrupts to stall? No, it flushes records one by one, releasing the console lock, and enabling interrupts between them. Let's look at `legacy_kthread_func`. The console is locked and unlocked between records. Interrupts should be enabled after each record! If they are, CPU 1 *can* process IPIs and report RCU quiescent states.
It's been confirmed that `__console_unlock` does not disable interrupts, and the interrupts are disabled *inside* `serial8250_console_write`. Between records, when `console_flush_one
|
| 53/2 |
2026/07/21 00:39 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/printk/printk.c Name:__console_unlock]
Results: map[SourceCode:2929: static void __console_unlock(void)
2930: {
2931: console_locked = 0;
2932: up_console_sem();
2933: }
SourceFile:kernel/printk/printk.c]
|
| 54/2 |
2026/07/21 00:39 |
llm |
expert |
0m
Model:
Tokens:
input: 51620
output: 36
thoughts: 1992
Thoughts: **Analyzing a Potential RCU Grace Period Stalemate**
Okay, so here's the breakdown of what I'm thinking. This situation involves the kernel's console flushing mechanism and a potential hang related to RCU grace periods. Let's trace it through:
1. It begins with `console_locked` and a call to `up_console_sem()`. Importantly, it *doesn't* do a `cond_resched()`. This is key. It implies that `legacy_kthread_func` is potentially running in a tight, unyielding loop.
2. If this kernel thread is in a tight loop without yielding, could it prevent RCU grace periods from completing? Since this is `PREEMPT_RT`, `rcu_preempt` is in play. Meaning a kernel task can be preempted. If `legacy_kthread_func` is preempted, it can report a quiescent state. However, if it's the *highest* priority task, or if there are no other tasks, it will keep running, potentially indefinitely.
3. But, RCU actually forces quiescent states with IPIs! Even if there's a tight loop, as long as interrupts are enabled, the RCU IPI *should* be received. The interrupt handler should force the quiescent state, and the task could be preempted after the interrupt handler returns. Crucially, the code doesn't disable preemption anywhere, except in a specific part of `serial8250_console_write`.
4. So, `legacy_kthread_func` *should* be preemptable. The `console_lock()` acquires a semaphore, but semaphores don't disable preemption. The call to `console_srcu_read_lock` doesn't disable preemption, either.
5. Here's the problem. The *only* place preemption might be disabled is in `serial8250_console_write`. This is where it gets interesting: what if `serial8250_console_write` takes a *very* long time to write *one* console record?
6. Based on prior calculations, if the baud rate is absurdly low (like 1), it takes an insane amount of time to write. With a baud rate of 1, transmitting 1024 characters takes 10,240 seconds with interrupts disabled.
7. If interrupts are disabled for a very long time, RCU grace periods cannot complete! The soft lockup watchdog *would* fire, but the process has touched the soft lockup watchdog, so it wouldn't fire on CPU 1. CPU 0 *would* get a soft lockup if it tried to send an IPI to CPU 1. The hung task detector *would* fire because tasks are blocked waiting for RCU grace periods.
8. This means that the *only* way this can happen is if `serial8250_console_write` is taking an extremely long time for a *single* record. Which means the baud rate *must* be ridiculously low.
9. Now, the question becomes, how could the baud rate be so low? Two possibilities arise: either syzkaller intentionally set it via `ioctl(TCSETS)` on `/dev/ttyS0`, or there's a kernel bug. Syzkaller is running as root. This is a possibility.
10. If syzkaller is setting the baud rate, is this a security vulnerability? No, because that requires root privileges. This means it's a misconfiguration by the privileged user.
11. Is there any way an unprivileged user could trigger this? Can a pty somehow link to the console? No. Unprivileged users can't use `TIOCSSERIAL`.
12. Okay, let's eliminate other possibilities: What if the hardware is removed or offline and `serial_lsr_in` returns 0? It would spin forever until the timeout reaches 0. If timeout is normal (e.g., 10000), it takes only 10 milliseconds to spin. For 1024 characters, it would be 10 seconds. Even a dead serial port would not result in the 143 seconds.
13. However, the code *enables* interrupts between records. So, if RCU grace periods are the issue, even with a low baud rate, they *should* complete. It's unlocking, and allowing preemption.
14. `console_flush_one_record` calls `console_emit_next_record`. This goes to `con->write()`. For the 8250 driver, this becomes `serial8250_console_write`. Crucially, `serial8
|
| 55/2 |
2026/07/21 00:39 |
tool |
codesearch-definition-source |
0m
Error:
Args: map[ContextFile:include/linux/workqueue.h Name:WQ_UNBOUND]
Results: map[SourceCode: SourceFile:]
|
| 56/2 |
2026/07/21 00:39 |
llm |
expert |
0m
Model:
Tokens:
input: 54694
output: 32
thoughts: 22
Thoughts: Okay, here's my summary, presented as a stream of thought:
**Diving into the Workqueue Code**
Alright, I need to understand this `WQ_UNBOUND` flag. Seems like it's a critical component of the workqueue mechanism. Let's start with the standard approach: I'll head straight to the source. The natural place to begin is the `include/linux/workqueue.h` header file. That's where all the fundamental declarations and definitions related to workqueues should reside. My instinct tells me that the definition and any related comments or documentation explaining the purpose of this particular flag will be located there. I'll search for the exact string, `WQ_UNBOUND`, within the file, which should quickly lead me to the relevant code.
|
| 57/2 |
2026/07/21 00:40 |
tool |
grepper |
0m
Args: map[Expression:WQ_UNBOUND PathPrefix:include/linux/workqueue.h]
Results: map[Output:include/linux/workqueue.h=371=enum wq_flags {
include/linux/workqueue.h-372- WQ_BH = 1 << 0, /* execute in bottom half (softirq) context */
include/linux/workqueue.h:373: WQ_UNBOUND = 1 << 1, /* not bound to any cpu */
include/linux/workqueue.h-374- WQ_FREEZABLE = 1 << 2, /* freeze during suspend */
--
include/linux/workqueue.h=418=enum wq_consts {
include/linux/workqueue.h-419- WQ_MAX_ACTIVE = 2048, /* I like 2048, better ideas? */
include/linux/workqueue.h:420: WQ_UNBOUND_MAX_ACTIVE = WQ_MAX_ACTIVE,
include/linux/workqueue.h-421- WQ_DFL_ACTIVE = WQ_MAX_ACTIVE / 2,
--
include/linux/workqueue.h-456- * *_power_efficient_wq are inclined towards saving power and converted
include/linux/workqueue.h:457: * into WQ_UNBOUND variants if 'wq_power_efficient' is enabled; otherwise,
include/linux/workqueue.h-458- * they are same as their non-power-efficient counterparts - e.g.
--
include/linux/workqueue.h=560=alloc_workqueue_lockdep_map(const char *fmt, unsigned int flags, int max_active,
--
include/linux/workqueue.h-579-#define alloc_ordered_workqueue_lockdep_map(fmt, flags, lockdep_map, args...) \
include/linux/workqueue.h:580: alloc_hooks(alloc_workqueue_lockdep_map(fmt, WQ_UNBOUND | __WQ_ORDERED | (flags),\
include/linux/workqueue.h-581- 1, lockdep_map, ##args))
--
include/linux/workqueue.h-597-#define alloc_ordered_workqueue(fmt, flags, args...) \
include/linux/workqueue.h:598: alloc_workqueue(fmt, WQ_UNBOUND | __WQ_ORDERED | (flags), 1, ##args)
include/linux/workqueue.h-599-#define devm_alloc_ordered_workqueue(dev, fmt, flags, args...) \
include/linux/workqueue.h:600: devm_alloc_workqueue(dev, fmt, WQ_UNBOUND | __WQ_ORDERED | (flags), 1, ##args)
include/linux/workqueue.h-601-
--
include/linux/workqueue.h-604-#define create_freezable_workqueue(name) \
include/linux/workqueue.h:605: alloc_workqueue("%s", __WQ_LEGACY | WQ_FREEZABLE | WQ_UNBOUND | \
include/linux/workqueue.h-606- WQ_MEM_RECLAIM, 1, (name))
]
|
| 58/2 |
2026/07/21 00:40 |
llm |
expert |
0m
Model:
Tokens:
input: 55704
output: 32
thoughts: 158
Thoughts: **Digging into the Cgroup Offline Workqueue**
Okay, so I'm looking at this `alloc_workqueue("cgroup_offline", WQ_PERCPU, 1)` call and something feels a bit off. Let me double-check the source code in `kernel/cgroup/cgroup.c` just to be sure. Yep, there it is: `cgroup_offline_wq = alloc_workqueue("cgroup_offline", WQ_PERCPU, 1);`. Hang on a second... didn't I just see `WQ_PERCPU` show up in that grepper output? Let me confirm... No, the grepper output was exactly the same as the line of code: `cgroup_offline_wq = alloc_workqueue("cgroup_offline", WQ_PERCPU, 1);`. My intuition is telling me something is wrong here because `WQ_PERCPU` doesn't immediately jump out as being a member of `wq_flags`. Alright, let's see if this flag is even defined anywhere in the headers.
|
| 59/2 |
2026/07/21 00:40 |
tool |
grepper |
0m
Args: map[Expression:WQ_PERCPU PathPrefix:include/linux/workqueue.h]
Results: map[Output:include/linux/workqueue.h=371=enum wq_flags {
--
include/linux/workqueue.h-405- WQ_POWER_EFFICIENT = 1 << 7,
include/linux/workqueue.h:406: WQ_PERCPU = 1 << 8, /* bound to a specific cpu */
include/linux/workqueue.h-407-
--
include/linux/workqueue.h-414- /* BH wq only allows the following flags */
include/linux/workqueue.h:415: __WQ_BH_ALLOWS = WQ_BH | WQ_HIGHPRI | WQ_PERCPU,
include/linux/workqueue.h-416-};
--
include/linux/workqueue.h=560=alloc_workqueue_lockdep_map(const char *fmt, unsigned int flags, int max_active,
--
include/linux/workqueue.h-602-#define create_workqueue(name) \
include/linux/workqueue.h:603: alloc_workqueue("%s", __WQ_LEGACY | WQ_MEM_RECLAIM | WQ_PERCPU, 1, (name))
include/linux/workqueue.h-604-#define create_freezable_workqueue(name) \
]
|
| 60/2 |
2026/07/21 00:40 |
llm |
expert |
0m
Model:
Tokens:
input: 56463
output: 38
thoughts: 3551
Thoughts: **Root Cause Analysis of Hung Task and RCU Stall**
Okay, let's break this down step by step. I'm looking at a situation where a task is hung, and I think it's related to a potential RCU stall and a per-CPU workqueue. It looks like the `cgroup_offline_wq` workqueue isn't making progress, which is holding up the `offline_waitq`. The work item `css_killed_work_fn` isn't executing, and that's the key.
First, I consider that the workqueue on CPU 0 might be blocked, but the system should create a new worker, unless `max_active` is reached. In this case, `max_active` is one. So, if there is no other work item running, the work should be able to execute!
Next, I reason that maybe the RCU grace period isn't completing. This is where things get interesting. I see a note about CPU 1 being stuck in `serial8250_console_write` with interrupts disabled. A long-running serial console write with a very low baud rate *could* cause a long-running critical section, preventing RCU grace periods from completing. This also means the soft lockup watchdog will not fire.
I analyze that, if the baud rate is set to an extremely low value, a single console record *could* block for an extended period, for a long grace period. However, it looks like `legacy_kthread_func` enables interrupts between records, meaning this shouldn't be a problem unless a *single* record is taking a long time. However, I calculated that a full record would take a very long time, but it would have to be set by root, which means that unprivileged users can't trigger the issue.
I then check for other issues that could cause an extended spin in `wait_for_lsr`, like a corrupted `frame_time`, or a very slow baud rate that would only be settable by root.
I then look into whether Syzkaller could be triggering this, but conclude that's unlikely since serial console devices managed by Syzkaller would not be using `8250_port.c`.
I then try to assess whether or not the hung task is related to the serial console, since the NMI backtrace includes the soft lockup notation. However, a soft lockup *was* a past event. The current issue is a hung task. I determine this from the NMI backtrace with a hung task and an incomplete `offline_waitq`.
The root cause of the hung task is because `css_killed_work_fn` is not executing, which means that work is blocked by a work item. The work item is not queued. Because the work is queued with `queue_rcu_work`, that means an RCU grace period is not completing.
The problem is that many tasks are holding `rcu_read_lock`, but the key one is `pr/legacy/17`, which calls `serial8250_console_write`, which holds a lot of different locks. However, because it is in an RT kernel, `spin_lock` is an RT mutex, and requires that an RCU grace period is in place.
|
| 61/2 |
2026/07/21 00:40 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/locking/spinlock_rt.c Name:rt_spin_lock]
Results: map[SourceCode: 54: void __sched rt_spin_lock(spinlock_t *lock) __acquires(RCU)
55: {
56: spin_acquire(&lock->dep_map, 0, 0, _RET_IP_);
57: __rt_spin_lock(lock);
58: }
SourceFile:kernel/locking/spinlock_rt.c]
|
| 62/2 |
2026/07/21 00:40 |
llm |
expert |
0m
Model:
Tokens:
input: 60867
output: 39
thoughts: 20
Thoughts: Here's my attempt at summarizing the thought process, tailored for an expert audience and written in the first person:
**Kernel Concurrency Quandary**
Okay, hold on a second... my mental model is a bit off here. I'm seeing this `__rt_spin_lock` function, and my immediate expectation is that it's handling the spinlock acquisition directly. But the code trace... wait, is this right? Does this `__rt_spin_lock` *also* acquire an `rcu_read_lock`?
That just struck me as odd, and I have to reconsider the implications of this. A real-time spinlock *within* an RCU read critical section? That's not the first thing I would expect, so I have to double-check my understanding of the preemption model and the guarantees being provided. I need to understand why this would be necessary, or if perhaps there's a misunderstanding of some sort. If it does, indeed, involve nested locking, I now need to consider the implications on blocking behavior or, indeed, the intended functionality of that implementation. I'm going to have to dig deeper into the surrounding code and the intended synchronization scheme to figure out why this combination is happening. What's the high-level purpose here? Are we dealing with something that requires both read-side RCU protection *and* the atomicity of a spinlock for some critical section? Or is there some subtle interaction I'm missing? I should refresh my memory of the context.
|
| 63/2 |
2026/07/21 00:40 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/locking/spinlock_rt.c Name:__rt_spin_lock]
Results: map[SourceCode: 46: static __always_inline void __rt_spin_lock(spinlock_t *lock)
47: {
48: rtlock_might_resched();
49: rtlock_lock(&lock->lock);
50: rcu_read_lock();
51: migrate_disable();
52: }
SourceFile:kernel/locking/spinlock_rt.c]
|
| 64/2 |
2026/07/21 00:40 |
llm |
expert |
0m
Model:
Tokens:
input: 61369
output: 40
thoughts: 1016
Thoughts: **RCU Grace Period Blockage Root Cause Analysis**
Okay, so here's what's hitting me. I've got this `PREEMPT_RT` system, and I'm seeing RCU grace periods getting blocked. Let's trace this back. I'm seeing that the `__rt_spin_lock` function calls `rcu_read_lock()`. That's a key observation.
This means ANY task that holds a spinlock in `PREEMPT_RT` is inherently also holding an RCU read lock. And `pr/legacy/17` is the culprit, holding `port_lock_key`, which is `port->lock`. So `pr/legacy/17` is *also* holding `rcu_read_lock()` while inside `serial8250_console_write`.
The real kicker is that `serial8250_console_write` is taking a **very** long time β like, 143 seconds. That means `pr/legacy/17` is holding `rcu_read_lock()` for the *entire* duration. That's a huge problem. Holding `rcu_read_lock()` that long blocks RCU grace periods completely. It explains why `queue_rcu_work` is stuck, why `css_killed_work_fn` isn't running, and why `cgroup_lock_and_drain_offline` is hung.
So, the core issue is: `serial8250_console_write` is hogging `port->lock` (and thus `rcu_read_lock()`), holding it up for way too long. It's because it's writing to the serial console, a slow device. But why is it taking so long? Is it taking 143 seconds per record?
If it's writing at a normal baud rate (like 115200), each record would take around 90ms. But 90ms would release the spinlock, releasing `rcu_read_lock()`. And since `rcu_read_unlock()` is called when the spinlock is released in `PREEMPT_RT`, this SHOULD allow grace periods to complete since the read-side critical section ends. So, if it only takes 90ms per record, RCU grace periods WILL complete, and the problem doesn't exist.
Therefore, for the grace period to be blocked for 143 seconds, each record MUST take 143 seconds. That only happens if the baud rate is absurdly low, or if there's a serious hardware issue where `wait_for_lsr` is spinning for ages. But let's check. Even with a broken `serial_lsr_in`, `wait_for_lsr` will only spin for `tmout`, which in turn depends on the `baud` rate.
With a baud rate of 115200, the timeout is very short, leading to only 178ms per record at most. So, the only way to get a 143-second delay is if `tmout` is ENORMOUS. And a huge `tmout` only happens if `baud` is very low. This is only set by root.
Is there any other way `tmout` can be huge? What about uninitialized `up->port.frame_time`? If it's 0, then the delay is only 10 seconds. Nope. Still not 143.
Could it be memory corruption corrupting `up->port.frame_time`? It's exploitable, but there's no evidence of corruption.
Could `baud` be set to zero? That's interesting, let me check `uart_update_timeout`... Wait... Division by zero! Let me re-examine that function...
|
| 65/2 |
2026/07/21 00:40 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/serial_core.c Name:uart_update_timeout]
Results: map[SourceCode: 432: /**
433: * uart_update_timeout - update per-port frame timing information
434: * @port: uart_port structure describing the port
435: * @cflag: termios cflag value
436: * @baud: speed of the port
437: *
438: * Set the @port frame timing information from which the FIFO timeout value is
439: * derived. The @cflag value should reflect the actual hardware settings as
440: * number of bits, parity, stop bits and baud rate is taken into account here.
441: *
442: * Locking: caller is expected to take @port->lock
443: */
444: void
445: uart_update_timeout(struct uart_port *port, unsigned int cflag,
446: unsigned int baud)
447: {
448: u64 temp = tty_get_frame_size(cflag);
449:
450: temp *= NSEC_PER_SEC;
451: port->frame_time = (unsigned int)DIV64_U64_ROUND_UP(temp, baud);
452: }
SourceFile:drivers/tty/serial/serial_core.c]
|
| 66/2 |
2026/07/21 00:40 |
llm |
expert |
0m
Model:
Tokens:
input: 63630
output: 38
thoughts: 987
Thoughts: **Debugging a Potential Serial Console Hang**
Okay, let's break this down. My initial thought was that a zero `baud` rate would cause a divide-by-zero error in `DIV64_U64_ROUND_UP`, but I didn't see an exception, so `baud` isn't zero. That's good. Now, `uart_get_baud_rate` might return zero if `B0` is requested or the rate can't be met, but it would return 9600 if it can't be met and `B0` isn't requested. So, if `baud` was zero, `uart_update_timeout` would crash, and since it didn't, the `baud` isn't zero, or otherwise we would have seen that.
But, if `baud` is 50, then `frame_time` is 200ms. Following on, `tmout` would be 400,000, and 400,000 udelay(1) loops are equivalent to 400ms. A 400ms delay per character * 1024 characters means a record is 409 seconds, which *perfectly* matches the 143-second hung task! And 50 is a valid baud rate. But can an unprivileged user even *set* the baud rate to 50? No, they don't have access to the serial console device node.
Hmm, is there *another* way `wait_for_lsr` could spin for so long? What if `tmout` is "normal" but `udelay(1)` itself is taking forever? `udelay(1)` is a busy loop based on `loops_per_jiffy` or TSC. CPU frequency changes or a VM overload *might* slow it down, but not by a factor of 1000x! What about `touch_nmi_watchdog()`? No, that is not the issue.
Let's rethink. What if the problem *isn't* that writing one record takes forever, but that the spinlock in `pr/legacy` *never* releases? I should re-examine `serial8250_console_write`. It acquires the spinlock. It writes, then it releases. It definitely releases. So, it *must* be taking a long time *inside* the spinlock. That means writing the string, which implies `wait_for_lsr` spinning, which means `tmout` is huge, which means `baud` is low.
But is there *any* other possibility? Could `console_flush_one_record` be called with a HUGE `count`? Wait... it gets the record from the printk ring buffer. The max size of a printk record is LOG_LINE_MAX, which is 1024. Wait, does `console_flush_one_record` flush multiple records? No, it's *one* record. Let's verify by checking `console_flush_one_record`.
|
| 67/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/printk/printk.c Name:console_flush_one_record]
Results: map[SourceCode:3210: /*
3211: * Print out one record for each console.
3212: *
3213: * @do_cond_resched is set by the caller. It can be true only in schedulable
3214: * context.
3215: *
3216: * @next_seq is set to the sequence number after the last available record.
3217: * The value is valid only when all usable consoles were flushed. It is
3218: * when the function returns true (can do the job) and @try_again parameter
3219: * is set to false, see below.
3220: *
3221: * @handover will be set to true if a printk waiter has taken over the
3222: * console_lock, in which case the caller is no longer holding the
3223: * console_lock. Otherwise it is set to false.
3224: *
3225: * @try_again will be set to true when it still makes sense to call this
3226: * function again. The function could do the job, see the return value.
3227: * And some consoles still make progress.
3228: *
3229: * Returns true when the function could do the job. Some consoles are usable,
3230: * and there was no takeover and no panic_on_other_cpu().
3231: *
3232: * Requires the console_lock.
3233: */
3234: static bool console_flush_one_record(bool do_cond_resched, u64 *next_seq, bool *handover,
3235: bool *try_again)
3236: {
3237: struct console_flush_type ft;
3238: bool any_usable = false;
3239: struct console *con;
3240: int cookie;
3241:
3242: *try_again = false;
3243:
3244: printk_get_console_flush_type(&ft);
3245:
3246: cookie = console_srcu_read_lock();
3247: for_each_console_srcu(con) {
3248: short flags = console_srcu_read_flags(con);
3249: u64 printk_seq;
3250: bool progress;
3251:
3252: /*
3253: * console_flush_one_record() is only responsible for
3254: * nbcon consoles when the nbcon consoles cannot print via
3255: * their atomic or threaded flushing.
3256: */
3257: if ((flags & CON_NBCON) && (ft.nbcon_atomic || ft.nbcon_offload))
3258: continue;
3259:
3260: if (!console_is_usable(con, flags, !do_cond_resched))
3261: continue;
3262: any_usable = true;
3263:
3264: if (flags & CON_NBCON) {
3265: progress = nbcon_legacy_emit_next_record(con, handover, cookie,
3266: !do_cond_resched);
3267: } else {
3268: progress = console_emit_next_record(con, handover, cookie);
3269: }
3270:
3271: /*
3272: * If a handover has occurred, the SRCU read lock
3273: * is already released.
3274: */
3275: if (*handover)
3276: goto fail;
3277:
3278: /*
3279: * @con can be used here now that it is certain that this
3280: * context is still holding the SRCU read lock.
3281: */
3282: if (flags & CON_NBCON)
3283: printk_seq = nbcon_seq_read(con);
3284: else
3285: printk_seq = con->seq;
3286:
3287: /* Track the next of the highest seq flushed. */
3288: if (printk_seq > *next_seq)
3289: *next_seq = printk_seq;
3290:
3291: if (!progress)
3292: continue;
3293:
3294: /*
3295: * A usable console made progress. There might still be
3296: * pending messages.
3297: */
3298: *try_again = true;
3299:
3300: /* Allow panic_cpu to take over the consoles safely. */
3301: if (panic_on_other_cpu())
3302: goto fail_srcu;
3303:
3304: if (do_cond_resched)
3305: cond_resched();
3306: }
3307: console_srcu_read_unlock(cookie);
3308:
3309: return any_usable;
3310:
3311: fail_srcu:
3312: console_srcu_read_unlock(cookie);
3313: fail:
3314: *try_again = false;
3315: return false;
3316: }
SourceFile:kernel/printk/printk.c]
|
| 68/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 66846
output: 54
thoughts: 805
Thoughts: **RCU Stall Analysis: A Deep Dive into Console Flushing**
Okay, let's break this down. My initial thought is that `console_flush_one_record` can call `cond_resched()` when `do_cond_resched` is true, which is what `legacy_kthread_func` sets. That means a potential CPU yield, which allows RCU grace periods to complete, right? But `cond_resched()` only yields if `TIF_NEED_RESCHED` is set. Even if there's no yield, it calls `rcu_all_qs()` which should still report a quiescent state. So, `console_flush_one_record` *definitely* reports RCU quiescent states between records.
This suggests the 143-second stall is caused by a *single* record taking that long. The only reasonable explanation for this is a very low baud rate set by root.
But, hang on, is that the *only* way? What if `console_flush_one_record` is called with `do_cond_resched = false`? I have to look into this more! But `legacy_kthread_func` calls it with `true`! What about from `vprintk_emit`? Could a task synchronously flush the console? But the stack trace points to `legacy_kthread_func`, so it *must* be called with `true`, thus calling `cond_resched()`. Therefore the RCU stall is definitely caused by a single record taking an extended time, meaning a very low baud rate.
Is there any other possibility here? A huge `count` in `serial8250_console_write`? `console_emit_next_record` pulls the record from the ring buffer, but the maximum record size is `LOG_LINE_MAX` (1024), so that's a dead end.
What about `wait_for_xmitr` taking too long? This uses `wait_for_lsr` which spins for `tmout`. So it's the same situation.
An infinite loop inside `serial8250_console_write`? Let's check.
```c
if (likely(use_fifo))
serial8250_console_fifo_write(up, s, count);
else
uart_console_write(port, s, count, serial8250_console_wait_putchar);
```
`uart_console_write` is a simple loop with `putchar`.
```c
for (i = 0; i < count; i++) {
if (s[i] == '\n')
putchar(port, '\r');
putchar(port, s[i]);
}
```
It's a straightforward loop to `count`, and `count` is capped at 1024, so no infinite loop here. What about `serial8250_console_fifo_write`? Let's make sure that's also not stuck. I'm going to have to check that function next.
|
| 69/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:serial8250_console_fifo_write]
Results: map[SourceCode:3282: /*
3283: * Print a string to the serial port using the device FIFO
3284: *
3285: * It sends fifosize bytes and then waits for the fifo
3286: * to get empty.
3287: */
3288: static void serial8250_console_fifo_write(struct uart_8250_port *up,
3289: const char *s, unsigned int count)
3290: {
3291: const char *end = s + count;
3292: unsigned int fifosize = up->tx_loadsz;
3293: struct uart_port *port = &up->port;
3294: unsigned int tx_count = 0;
3295: bool cr_sent = false;
3296: unsigned int i;
3297:
3298: while (s != end) {
3299: /* Allow timeout for each byte of a possibly full FIFO */
3300: serial8250_fifo_wait_for_lsr_thre(up, fifosize);
3301:
3302: for (i = 0; i < fifosize && s != end; ++i) {
3303: if (*s == '\n' && !cr_sent) {
3304: serial8250_console_putchar(port, '\r');
3305: cr_sent = true;
3306: } else {
3307: serial8250_console_putchar(port, *s++);
3308: cr_sent = false;
3309: }
3310: }
3311: tx_count = i;
3312: }
3313:
3314: /*
3315: * Allow timeout for each byte written since the caller will only wait
3316: * for UART_LSR_BOTH_EMPTY using the timeout of a single character
3317: */
3318: serial8250_fifo_wait_for_lsr_thre(up, tx_count);
3319: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 70/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 69001
output: 59
thoughts: 188
Thoughts: **Analyzing the 8250 FIFO Wait Function**
Okay, so I'm looking at this `serial8250_fifo_wait_for_lsr_thre` function. I see it's calling `wait_for_lsr`, which is a common pattern in 8250 serial driver code, nothing unusual there. The interesting bit is how the timeout is being calculated before the `wait_for_lsr` call. Specifically, the line `tmout *= count;` jumps out at me. It's taking `up->port.frame_time * 2 / NSEC_PER_USEC`, which represents a per-character timeout in microseconds, and multiplying it by `count`, likely the number of bytes in the FIFO.
Hang on a second... isn't `wait_for_lsr` supposed to handle its own timeout calculations? I'm almost certain I've seen that function take the timeout as an *absolute* time, or perhaps based on clock cycles, not this per-count approach. This feels like a potential redundancy or even an error. It could be that `wait_for_lsr` is getting a timeout that's already scaled by the FIFO size, which would mean it's waiting for far longer than necessary. I need to double-check the `wait_for_lsr` function's internal calculations to confirm my suspicion. Let's dig deeper into the call stack and see what `wait_for_lsr` is actually doing with that `tmout` value. I'll need to verify if the scaling is correct, or if this multiplication is producing an unnecessarily long wait.
|
| 71/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:drivers/tty/serial/8250/8250_port.c Name:serial8250_fifo_wait_for_lsr_thre]
Results: map[SourceCode:3230: void serial8250_fifo_wait_for_lsr_thre(struct uart_8250_port *up, unsigned int count)
3231: {
3232: unsigned int i;
3233:
3234: for (i = 0; i < count; i++) {
3235: if (wait_for_lsr(up, UART_LSR_THRE))
3236: return;
3237: }
3238: }
SourceFile:drivers/tty/serial/8250/8250_port.c]
|
| 72/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 69782
output: 38
thoughts: 1059
Thoughts: **Analyzing a Potential Timeout in Serial Communication**
Okay, let's break this down. It seems we're looking at a potential hang related to serial communication, specifically around the `serial8250_fifo_wait_for_lsr_thre` function. I see that this function calls `wait_for_lsr` repeatedly, a number of times determined by the `count` variable. Critically, `wait_for_lsr` itself calculates its own timeout (`tmout`) internally.
If `wait_for_lsr` times out, it's called repeatedly, and the timeout value (`tmout`) is the amount of time each call takes. For a standard 115200 baud rate, this timeout is 174 microseconds. Now, if `count` is the size of the FIFO (e.g., 16), the total timeout becomes 2.7 milliseconds. Even with broken hardware that *never* asserts `UART_LSR_THRE`, this translates to only 2.7ms per chunk. For 1024 characters (64 chunks), that's just 172ms, which is nowhere near the 143 seconds we're trying to explain.
Therefore, the only way to get a timeout of 143 seconds is if the `tmout` value within `wait_for_lsr` is enormous. The only parameter that dictates the size of `tmout` is a *very* low `baud` rate.
So, could a low baud rate be the root cause? The next step is looking into how the `frame_time` is calculated. It appears to depend on `tty_get_frame_size` and the baud rate through the `uart_update_timeout` function:
```c
u64 temp = tty_get_frame_size(cflag);
temp *= NSEC_PER_SEC;
port->frame_time = (unsigned int)DIV64_U64_ROUND_UP(temp, baud);
```
Okay, `tty_get_frame_size` returns bits per frame. For example, 10 for 8N1. The formula correctly calculates the time per frame in nanoseconds. If the baud rate is 1, the timeout would be huge, as predicted. For 115200, it gives a reasonable timeout of 86805, or about 87 us per frame, and is therefore not the bug.
The conclusion is that the only way to produce the hang is to set a ridiculously low baud rate. But can an *unprivileged* user set the baud rate? No. So, we can rule out user-space exploitation.
Let's look for other potential areas. Could the issue be unrelated to serial and stem from a hang in `cgroup_lock_and_drain_offline`? We see it's waiting on `offline_waitq`. Is it possible the wait queue is never woken up, despite `css_killed_work_fn` executing? Let's check `css_killed_work_fn`:
```c
do {
offline_css(css);
css_put(css);
/* @css can't go away while we're holding cgroup_mutex */
css = css->parent;
} while (css && atomic_dec_and_test(&css->online_cnt));
```
Yep, it calls `offline_css(css)`. And `offline_css` *does* call `wake_up_all(&css->cgroup->offline_waitq);`, so it should definitely wake up the `waitq`.
Is it possible that `cgroup_lock_and_drain_offline` simply misses the wakeup? Let's examine that function:
```c
DEFINE_WAIT(wait);
if (!css || !css_is_dying(css))
continue;
cgroup_get_live(dsct);
prepare_to_wait(&dsct->offline_waitq, &wait,
TASK_UNINTERRUPTIBLE);
cgroup_unlock();
schedule();
finish_wait(&dsct->offline_waitq, &wait);
```
Aha! `cgroup_lock_and_drain_offline` *does* check `css_is_dying(css)`. If the CSS *is* dying, it prepares to wait, unlocks, and schedules. The critical race condition is the timing: What if `offline_css` is called *before* `prepare_to_wait`?
If `offline_css` has already
|
| 73/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:include/linux/cgroup.h Name:css_is_dying]
Results: map[SourceCode: 398: /**
399: * css_is_dying - test whether the specified css is dying
400: * @css: target css
401: *
402: * Test whether @css is in the process of offlining or already offline. In
403: * most cases, ->css_online() and ->css_offline() callbacks should be
404: * enough; however, the actual offline operations are RCU delayed and this
405: * test returns %true also when @css is scheduled to be offlined.
406: *
407: * This is useful, for example, when the use case requires synchronous
408: * behavior with respect to cgroup removal. cgroup removal schedules css
409: * offlining but the css can seem alive while the operation is being
410: * delayed. If the delay affects user visible semantics, this test can be
411: * used to resolve the situation.
412: */
413: static inline bool css_is_dying(struct cgroup_subsys_state *css)
414: {
415: return css->flags & CSS_DYING;
416: }
SourceFile:include/linux/cgroup.h]
|
| 74/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 72259
output: 50
thoughts: 43
Thoughts: Okay, here's my interpretation of that thought process, from an expert's perspective:
**Debugging a Potentially Troubling CSS Scenario**
Right, so `css_is_dying` is checking the value of `CSS_DYING`. Naturally, my mind immediately jumps to the question of *when* that variable is actually being set. This implies some kind of broader system health check or feature flag, and the name "CSS_DYING" certainly raises an eyebrow! I need to trace back through the code to identify the points where `CSS_DYING` is modified. Knowing the context and conditions under which it's set is crucial to understanding what's going on and determining if there's a genuine problem, or if it's a false alarm.
|
| 75/2 |
2026/07/21 00:41 |
tool |
codesearch-find-references |
0m
Error:
Args: map[ContextFile:kernel/cgroup/cgroup.c IncludeSnippetLines:0 Name:CSS_DYING SourceTreePrefix:]
Results: map[References:<nil> TruncatedOutput:false]
|
| 76/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 72535
output: 29
thoughts: 12
Thoughts: Here's my attempt at summarizing the thought process, tailored for an expert audience:
**Analyzing the Significance of a Flag**
Okay, so I'm processing some code and I see this flag, `CSS_DYING`. My initial reaction is that it's just a variable name, but then I stop. "Wait a minute," I think, "that's a flag." A flag in a system is rarely just a name, it's a state indicator. It implies that a specific condition or transition has taken place, and that downstream code *needs* to know about it. In this case, itβs about CSS. So, this flag likely signals that CSS is in some kind of critical state, potentially a deprecation, a removal, or some type of transition. It is the beginning of the end for the module. I need to understand what state this flag represents, what code sets it, and most crucially, how the system behaves when it's true. This is a crucial indicator. My next step has to be to trace where it's set and used.
|
| 77/2 |
2026/07/21 00:41 |
tool |
grepper |
0m
Args: map[Expression:CSS_DYING PathPrefix:kernel/cgroup/]
Results: map[Output:kernel/cgroup/cgroup.c=779=static void css_update_populated(struct cgroup_subsys_state *css, bool populated)
--
kernel/cgroup/cgroup.c-811- * Pair with smp_mb() in kill_css_sync(). Either we observe
kernel/cgroup/cgroup.c:812: * CSS_DYING and queue, or the caller observes our decrement
kernel/cgroup/cgroup.c-813- * and fires synchronously.
--
kernel/cgroup/cgroup.c=6111=static void kill_css_sync(struct cgroup_subsys_state *css)
--
kernel/cgroup/cgroup.c-6116-
kernel/cgroup/cgroup.c:6117: if (css->flags & CSS_DYING)
kernel/cgroup/cgroup.c-6118- return;
--
kernel/cgroup/cgroup.c-6120- /*
kernel/cgroup/cgroup.c:6121: * Call css_killed(), if defined, before setting the CSS_DYING flag
kernel/cgroup/cgroup.c-6122- */
--
kernel/cgroup/cgroup.c-6125-
kernel/cgroup/cgroup.c:6126: css->flags |= CSS_DYING;
kernel/cgroup/cgroup.c-6127-
--
kernel/cgroup/cgroup.c-6130- * caller observes the walker's decrement and fires
kernel/cgroup/cgroup.c:6131: * synchronously, or the walker observes CSS_DYING and queues.
kernel/cgroup/cgroup.c-6132- */
]
|
| 78/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 73250
output: 43
thoughts: 555
Thoughts: **Analyzing a Potential Race Condition in Cgroup Offline Handling**
Okay, so here's what's running through my head. We have `kill_css_sync` being called during a cgroup kill event, and it sets the `CSS_DYING` flag. Subsequently, `css_killed_ref_fn` is called, followed by `css_killed_work_fn` and then `offline_css`. The `offline_css` function is designed to wake up the `offline_waitq`. The concern I have is, if `offline_css` gets called *before* `cgroup_lock_and_drain_offline` checks `css_is_dying`, then `cgroup_lock_and_drain_offline` might incorrectly see `CSS_DYING` is still set.
The reason this is a problem, is because `offline_css` does *not* clear `CSS_DYING`. It only clears `CSS_ONLINE`. Specifically, this function clears the online flag, removes the subsystem reference, and wakes up the waitqueue. So even after it does its thing, `css_is_dying` will still return true, at least initially.
If `css_is_dying` returns true, `cgroup_lock_and_drain_offline` is supposed to call `prepare_to_wait`, unlock, and then `schedule()`. But the issue is, `offline_waitq` has already been woken up by `offline_css`! It seems like this might lead to a forever sleep situation.
Then I realized something crucial. `cgroup_lock_and_drain_offline` holds the `cgroup_mutex` when it checks `css_is_dying`. Furthermore, `offline_css` ALSO holds the `cgroup_mutex` when it wakes up `offline_waitq`. They are mutually exclusive operations, which indicates the design may work. If `offline_css` has already run, it must have acquired and released the mutex.
If `cgroup_lock_and_drain_offline` runs AFTER `offline_css`, it will indeed see the `CSS_DYING` flag is still set. Here's where it gets interesting, if it sees `CSS_DYING`, it tries to sleep on `offline_waitq`. BUT the `offline_waitq` is ALREADY awake at that point.
Given this, the code is supposed to be structured to prevent the forever sleep, by checking and handling the wake up, but I need to investigate `cgroup_lock_and_drain_offline` to make sure it functions as expected. Is this a bug in `cgroup_lock_and_drain_offline`? I'm now going to re-examine that function.
|
| 79/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:kernel/cgroup/cgroup.c Name:cgroup_lock_and_drain_offline]
Results: map[SourceCode:3243: /**
3244: * cgroup_lock_and_drain_offline - lock cgroup_mutex and drain offlined csses
3245: * @cgrp: root of the target subtree
3246: *
3247: * Because css offlining is asynchronous, userland may try to re-enable a
3248: * controller while the previous css is still around. This function grabs
3249: * cgroup_mutex and drains the previous css instances of @cgrp's subtree.
3250: */
3251: void cgroup_lock_and_drain_offline(struct cgroup *cgrp)
3252: __acquires(&cgroup_mutex)
3253: {
3254: struct cgroup *dsct;
3255: struct cgroup_subsys_state *d_css;
3256: struct cgroup_subsys *ss;
3257: int ssid;
3258:
3259: restart:
3260: cgroup_lock();
3261:
3262: cgroup_for_each_live_descendant_post(dsct, d_css, cgrp) {
3263: for_each_subsys(ss, ssid) {
3264: struct cgroup_subsys_state *css = cgroup_css(dsct, ss);
3265: DEFINE_WAIT(wait);
3266:
3267: if (!css || !css_is_dying(css))
3268: continue;
3269:
3270: cgroup_get_live(dsct);
3271: prepare_to_wait(&dsct->offline_waitq, &wait,
3272: TASK_UNINTERRUPTIBLE);
3273:
3274: cgroup_unlock();
3275: schedule();
3276: finish_wait(&dsct->offline_waitq, &wait);
3277:
3278: cgroup_put(dsct);
3279: goto restart;
3280: }
3281: }
3282: }
SourceFile:kernel/cgroup/cgroup.c]
|
| 80/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 75054
output: 36
thoughts: 94
Thoughts: **Analyzing the cgroup_css Interaction**
Okay, let me think this through. The function `cgroup_css(dsct, ss)` is supposed to give me a specific subsystem's CSS, and it appears to simply be returning `dsct->subsys[ss->id]`. But then I see this in `offline_css`: `RCU_INIT_POINTER(css->cgroup->subsys[ss->id], NULL);`. Aha! That means if `offline_css` has already executed, `cgroup_css` is going to return NULL for that subsystem! This is important. I need to verify this behavior thoroughly. I can see potential problems here if I'm not careful. I'll need to write some checks to make sure this is what's happening in my specific context and that I'm handling the NULL return properly. Gotta be diligent.
|
| 81/2 |
2026/07/21 00:41 |
tool |
codesearch-definition-source |
0m
Args: map[ContextFile:include/linux/cgroup.h Name:cgroup_css]
Results: map[SourceCode: 377: /**
378: * cgroup_css - obtain a cgroup's css for the specified subsystem
379: * @cgrp: the cgroup of interest
380: * @ss: the subsystem of interest (%NULL returns @cgrp->self)
381: *
382: * Return @cgrp's css (cgroup_subsys_state) associated with @ss. This
383: * function must be called either under cgroup_mutex or rcu_read_lock() and
384: * the caller is responsible for pinning the returned css if it wants to
385: * keep accessing it outside the said locks. This function may return
386: * %NULL if @cgrp doesn't have @subsys_id enabled.
387: */
388: static inline struct cgroup_subsys_state *cgroup_css(struct cgroup *cgrp,
389: struct cgroup_subsys *ss)
390: {
391: if (CGROUP_HAS_SUBSYS_CONFIG && ss)
392: return rcu_dereference_check(cgrp->subsys[ss->id],
393: lockdep_is_held(&cgroup_mutex));
394: else
395: return &cgrp->self;
396: }
SourceFile:include/linux/cgroup.h]
|
| 82/2 |
2026/07/21 00:41 |
llm |
expert |
0m
Model:
Tokens:
input: 75769
output: 66
thoughts: 1370
Thoughts: **Analysis of the Cgroup Offlining Hang**
Okay, let's break this down systematically. So, `cgroup_css` grabs the relevant CSS structure from the `subsys` array, and `offline_css` sets that entry to NULL. That's key. If `offline_css` has run, `cgroup_css` will return NULL. Now, `cgroup_lock_and_drain_offline` checks for `NULL` CSS entries and skips them. Therefore, the sleep only happens *before* `offline_css` runs. Which means `css_killed_work_fn` hasn't run. `css_killed_work_fn` is blocked because it's waiting on an RCU grace period. The RCU grace period is, in turn, blocked by CPU 1 being stuck in `serial8250_console_write`, holding `rcu_read_lock()` through `rt_spin_lock`.
So, the core problem is a soft lockup in the serial console driver. This blocks RCU grace periods in `PREEMPT_RT` kernels (or with generally slow serial consoles), which stalls cgroup offlining, leading to a hung task. Classic, well-understood issue. Now, the real question: is this exploitable? No, it's a denial of service (DoS) situation, not a memory corruption bug. Can an unprivileged user trigger this? Let's see. Changing the baud rate requires root privileges. What about a flood of `printk` output? Well, the analysis of the printk output is that RCU grace periods WILL complete between records. A huge amount of printk won't block RCU grace periods for 143 seconds. It only blocks if a single record takes 143 seconds. That requires a very low baud rate, which requires root.
So, not accessible from an unprivileged process. Let's dig deeper: Is there any way a single record can take 143 seconds without a low baud rate? The `console_flush_one_record` function limits size to LOG_LINE_MAX. However, might serial8250_console_write be called from another place? Maybe during a kernel oops? It seems it's always called from `console_flush_one_record`. So, size is limited to 1024.
What if the serial port is a virtual device created by Syzkaller, which might intentionally delay I/O? Yes, syzkaller could create a virtual device that intercepts the inb and intentionally delays it. But syzkaller can only do this if it has access to /dev/port or if it's running in a VM guest, where the host can cause the delay. Access to /dev/port requires root. Even if it's a VM guest and the host delays the I/O, that's a host-level issue not a guest kernel issue. Again, inaccessible from unprivileged processes.
Therefore, this bug:
- Is not exploitable.
- Results in a DoS (soft lockup/hung task).
- Cannot be triggered by unprivileged processes.
- Cannot be triggered from user namespaces, because of missing device nodes.
Now, let me categorize the results:
- Exploitable: False
- DenialOfService: True
- Unprivileged: False
- UserNamespace: False
- VMGuestTrigger: False (we only evaluate the guest kernel)
- VMHostTrigger: False
- NetworkTrigger: False
- RemoteTrigger: False
- PeripheralTrigger: False (a malicious USB serial device could cause a hang if it's used as a console, but USB serial devices don't use serial8250.c).
Could a malicious USB device emulate a PCI device? Yes, a malicious peripheral plugged in via Thunderbolt/PCIe could emulate an 8250 UART. Could it then be used as a console and delay the inb operation and cause a delay? Yes. It could emulate an 8250 UART. Does this mean it is automatically a console? No. Usually, the console is specified on the kernel command line. A hotplugged PCIe device won't become the console unless specifically configured. So, a malicious peripheral can't easily trigger this. Therefore, PeripheralTrigger: False.
Let me review:
- Exploitable: No.
- Denial Of Service: Yes, it's a soft lockup / hung task.
- Accessible From Unprivileged Processes: No.
- Accessible From User Namespaces: No.
- VM Guest Trigger: No.
- VM Host Trigger: No.
- Ethernet Network Trigger: No.
- Other Remote Trigger: No.
- Peripheral Trigger: No.
- Malicious Filesystem Trigger: No.
I'm now ready to call
|
| 83/2 |
2026/07/21 00:42 |
tool |
set-results |
0m
Args: map[DenialOfService:true Exploitable:false FilesystemTrigger:false NetworkTrigger:false PeripheralTrigger:false RemoteTrigger:false Unprivileged:false UserNamespace:false VMGuestTrigger:false VMHostTrigger:false]
Results: map[DenialOfService:true Exploitable:false FilesystemTrigger:false NetworkTrigger:false PeripheralTrigger:false RemoteTrigger:false Unprivileged:false UserNamespace:false VMGuestTrigger:false VMHostTrigger:false]
|
| 84/2 |
2026/07/21 00:42 |
llm |
expert |
0m
Model:
Tokens:
input: 78294
output: 769
thoughts: 369
Thoughts: **My Analysis of the Hung Task**
Okay, the data is in, and I can start synthesizing a response. Let's see, the key here is the hung task is `cgroup_lock_and_drain_offline`, waiting on `offline_waitq`. I remember that structure, and recall it is awakened by `css_killed_work_fn`, queued via `queue_rcu_work`. `queue_rcu_work` itself waits for an RCU grace period. Ah, and that's where the bottleneck is. The RCU grace period is blocked because CPU 1 is stuck in `serial8250_console_write`, holding `port->lock`.
This is PREEMPT_RT, so `spin_lock` (which `port->lock` is) also acquires `rcu_read_lock()`. Now, itβs coming back to me β if `serial8250_console_write` takes an extraordinarily long time, let's say due to a very low baud rate like 50, where a single large buffer takes over 100 seconds, it holds that `rcu_read_lock()` for an extended period. This prevents the RCU grace period from completing. Consequently, the cgroup offline process hangs, which the hung task detector flags.
It is interesting that configuring such a slow serial console requires root privileges β access to something like `/dev/ttyS0` or the `CAP_SYS_ADMIN` capability. Thus, an unprivileged user cannot trigger this behavior.
So, this boils down to a classic limitation of serial consoles in combination with `PREEMPT_RT` (or simply slow consoles). Itβs not a security vulnerability per se, but rather a Denial of Service stemming from a privileged userβs misconfiguration. This is a crucial distinction that needs to be clearly communicated.
|
| 85/1 |
2026/07/21 00:42 |
action |
format-explanation |
0m
Results: map[Explanation:Based on the analysis of the bug report and the kernel source code, here is the
assessment of the issue:
### Root Cause Analysis
The bug report indicates a hung task (`INFO: task syz... blocked for more than
143 seconds`) where a process is stuck in `cgroup_lock_and_drain_offline()`.
This function is waiting on the `offline_waitq` for a cgroup subsystem state
(css) to finish offlining.
The offlining process is handled asynchronously by `css_killed_work_fn()`, which
is queued using `queue_rcu_work()`. This means the work is only scheduled
*after* an RCU grace period completes.
The NMI backtrace reveals that CPU 1 is simultaneously stuck in `io_serial_in()`
inside `serial8250_console_write()`. Because this is a `PREEMPT_RT` kernel,
standard spinlocks (like the `port->lock` acquired in
`serial8250_console_write`) are implemented as RT-mutexes which implicitly
acquire `rcu_read_lock()` to prevent RCU grace periods from completing while the
lock is held.
If the serial console's baud rate is set to an extremely low value (e.g., 50
baud), writing a single 1024-byte printk record to the console can take hundreds
of seconds. Because `serial8250_console_write()` holds the port lock (and thus
`rcu_read_lock()`) for the entire duration of writing that single record, it
blocks all RCU grace periods system-wide for that duration.
Since the RCU grace period cannot complete, `queue_rcu_work()` never queues the
cgroup offlining work, `offline_waitq` is never woken up, and the task waiting
in `cgroup_lock_and_drain_offline()` hangs, eventually triggering the hung task
detector.
### Security Impact
**Exploitable:** False. This is a pure concurrency/timing issue caused by a slow
hardware interface blocking RCU. There is no memory corruption, out-of-bounds
access, or information leak involved.
**Denial of Service:** True. The bug results in a system-wide RCU stall and hung
tasks, effectively causing a denial of service.
**Accessible From Unprivileged Processes / User Namespaces:** False. To trigger
this issue, an attacker must force `serial8250_console_write()` to take an
excessively long time for a single record. This requires setting the serial
console's baud rate to a very low value via `ioctl(TCSETS)`. The serial console
device node (e.g., `/dev/ttyS0`) is restricted to `root` or the `dialout` group.
Unprivileged users, even within user namespaces, do not have the necessary
permissions to open the physical console device and change its baud rate.
While unprivileged users might be able to trigger a large volume of `printk`
messages (e.g., by triggering warnings), the console flushing mechanism
(`console_flush_one_record`) releases the lock and enables interrupts/preemption
between individual records. Therefore, RCU grace periods can normally complete
between records unless a *single* record takes an abnormally long time (which
strictly requires a low baud rate).
### Conclusion
This is a known architectural limitation of slow serial consoles interacting
with RCU and `PREEMPT_RT` locking semantics. It causes a Denial of Service, but
it requires root/administrative privileges to misconfigure the serial port baud
rate, making it a non-issue for unprivileged local attackers.]
|