no interfaces have a carrier
[ 26.605808][ T3854] 8021q: adding VLAN 0 to HW filter on device bond0
[ 26.615436][ T3854] eql: remember to turn off Van-Jacobson compression on your slave devices
Starting crond: OK
Starting sshd: OK
syzkaller
syzkaller login: [ 38.092562][ T4036] sftp-server (4036) used greatest stack depth: 21184 bytes left
Warning: Permanently added '10.128.1.90' (ED25519) to the list of known hosts.
2025/10/25 08:27:52 parsed 1 programs
[ 49.004346][ T4189] cgroup: Unknown subsys name 'net'
[ 49.136146][ T4189] cgroup: Unknown subsys name 'rlimit'
[ 50.434621][ T4189] Adding 124996k swap on ./swap-file. Priority:0 extents:1 across:124996k FS
[ 52.088803][ T4202] chnl_net:caif_netlink_parms(): no params data found
[ 52.438289][ T4202] bridge0: port 1(bridge_slave_0) entered blocking state
[ 52.448666][ T4202] bridge0: port 1(bridge_slave_0) entered disabled state
[ 52.457208][ T4202] device bridge_slave_0 entered promiscuous mode
[ 52.490884][ T4202] bridge0: port 2(bridge_slave_1) entered blocking state
[ 52.498189][ T4202] bridge0: port 2(bridge_slave_1) entered disabled state
[ 52.513392][ T4202] device bridge_slave_1 entered promiscuous mode
[ 52.542324][ T144] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 52.550243][ T144] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 52.613402][ T4202] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 52.636647][ T4202] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 52.655101][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 52.705747][ T4202] team0: Port device team_slave_0 added
[ 52.715381][ T4202] team0: Port device team_slave_1 added
[ 52.736655][ T154] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 52.748000][ T154] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 52.774283][ T4202] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 52.792176][ T4202] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 52.820649][ T4202] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 52.835644][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 52.863900][ T4202] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 52.870862][ T4202] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 52.897943][ T4202] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 53.045523][ T4202] device hsr_slave_0 entered promiscuous mode
[ 53.077039][ T4202] device hsr_slave_1 entered promiscuous mode
[ 53.530629][ T4202] netdevsim netdevsim3 netdevsim0: renamed from eth0
[ 53.575495][ T4202] netdevsim netdevsim3 netdevsim1: renamed from eth1
[ 53.599265][ T4202] netdevsim netdevsim3 netdevsim2: renamed from eth2
[ 53.627242][ T4202] netdevsim netdevsim3 netdevsim3: renamed from eth3
[ 53.814305][ T4202] 8021q: adding VLAN 0 to HW filter on device bond0
[ 53.838411][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 53.864086][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 53.874758][ T4202] 8021q: adding VLAN 0 to HW filter on device team0
[ 53.895660][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 53.904907][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 53.915626][ T9] bridge0: port 1(bridge_slave_0) entered blocking state
[ 53.922894][ T9] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 53.942290][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 53.951075][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 53.959755][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 53.969533][ T9] bridge0: port 2(bridge_slave_1) entered blocking state
[ 53.976615][ T9] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 53.990087][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 54.015645][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 54.024515][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 54.035663][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 54.047068][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 54.057332][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 54.066184][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 54.078076][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 54.086988][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 54.098541][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 54.109146][ T4202] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 54.224081][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 54.232789][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 54.246545][ T4202] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 54.266000][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 54.274865][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 54.295561][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 54.304877][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 54.316343][ T4202] device veth0_vlan entered promiscuous mode
[ 54.323844][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 54.333637][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 54.346570][ T4202] device veth1_vlan entered promiscuous mode
[ 54.367978][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan0: link becomes ready
[ 54.377134][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan1: link becomes ready
[ 54.386204][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 54.396746][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 54.407391][ T4202] device veth0_macvtap entered promiscuous mode
[ 54.418542][ T4202] device veth1_macvtap entered promiscuous mode
[ 54.435332][ T4202] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 54.444639][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 54.453907][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 54.462494][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 54.470841][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 54.482211][ T4202] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 54.491913][ T4202] netdevsim netdevsim3 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 54.500714][ T4202] netdevsim netdevsim3 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 54.509736][ T4202] netdevsim netdevsim3 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 54.519188][ T4202] netdevsim netdevsim3 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 54.541048][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 54.549722][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
2025/10/25 08:27:59 executed programs: 0
[ 54.782880][ T4202] syz-executor (4202) used greatest stack depth: 20448 bytes left
[ 55.109246][ T4276] chnl_net:caif_netlink_parms(): no params data found
[ 55.157982][ T4284] chnl_net:caif_netlink_parms(): no params data found
[ 55.180829][ T156] netdevsim netdevsim3 netdevsim3 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[ 55.329017][ T4284] bridge0: port 1(bridge_slave_0) entered blocking state
[ 55.336369][ T4284] bridge0: port 1(bridge_slave_0) entered disabled state
[ 55.344475][ T4284] device bridge_slave_0 entered promiscuous mode
[ 55.353752][ T4284] bridge0: port 2(bridge_slave_1) entered blocking state
[ 55.360803][ T4284] bridge0: port 2(bridge_slave_1) entered disabled state
[ 55.369001][ T4284] device bridge_slave_1 entered promiscuous mode
[ 55.425018][ T4284] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 55.437653][ T4276] bridge0: port 1(bridge_slave_0) entered blocking state
[ 55.445153][ T4276] bridge0: port 1(bridge_slave_0) entered disabled state
[ 55.456236][ T4276] device bridge_slave_0 entered promiscuous mode
[ 55.468836][ T4276] bridge0: port 2(bridge_slave_1) entered blocking state
[ 55.475982][ T4276] bridge0: port 2(bridge_slave_1) entered disabled state
[ 55.483739][ T4276] device bridge_slave_1 entered promiscuous mode
[ 55.498249][ T4284] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 55.518074][ T4280] chnl_net:caif_netlink_parms(): no params data found
[ 55.586081][ T4276] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 55.599439][ T4276] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 55.613132][ T4284] team0: Port device team_slave_0 added
[ 55.620661][ T4284] team0: Port device team_slave_1 added
[ 55.635894][ T4282] chnl_net:caif_netlink_parms(): no params data found
[ 55.691413][ T4276] team0: Port device team_slave_0 added
[ 55.701709][ T4276] team0: Port device team_slave_1 added
[ 55.714318][ T4284] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 55.721636][ T4284] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 55.747655][ T4284] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 55.769629][ T4287] chnl_net:caif_netlink_parms(): no params data found
[ 55.798910][ T4284] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 55.806086][ T4284] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 55.832313][ T4284] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 55.860841][ T4276] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 55.867902][ T4276] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 55.894316][ T4276] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 55.920580][ T4280] bridge0: port 1(bridge_slave_0) entered blocking state
[ 55.927957][ T4280] bridge0: port 1(bridge_slave_0) entered disabled state
[ 55.936158][ T4280] device bridge_slave_0 entered promiscuous mode
[ 55.953494][ T4276] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 55.960456][ T4276] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 55.986685][ T4276] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 56.009625][ T4280] bridge0: port 2(bridge_slave_1) entered blocking state
[ 56.017039][ T4280] bridge0: port 2(bridge_slave_1) entered disabled state
[ 56.024889][ T4280] device bridge_slave_1 entered promiscuous mode
[ 56.072471][ T4282] bridge0: port 1(bridge_slave_0) entered blocking state
[ 56.079657][ T4282] bridge0: port 1(bridge_slave_0) entered disabled state
[ 56.088227][ T4282] device bridge_slave_0 entered promiscuous mode
[ 56.108833][ T4280] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 56.130362][ T4282] bridge0: port 2(bridge_slave_1) entered blocking state
[ 56.137762][ T4282] bridge0: port 2(bridge_slave_1) entered disabled state
[ 56.145967][ T4282] device bridge_slave_1 entered promiscuous mode
[ 56.155886][ T4284] device hsr_slave_0 entered promiscuous mode
[ 56.163516][ T4284] device hsr_slave_1 entered promiscuous mode
[ 56.170008][ T4284] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 56.178346][ T4284] Cannot create hsr debugfs directory
[ 56.191870][ T4280] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 56.210493][ T4276] device hsr_slave_0 entered promiscuous mode
[ 56.217223][ T4276] device hsr_slave_1 entered promiscuous mode
[ 56.224020][ T4276] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 56.231648][ T4276] Cannot create hsr debugfs directory
[ 56.252333][ T4287] bridge0: port 1(bridge_slave_0) entered blocking state
[ 56.259430][ T4287] bridge0: port 1(bridge_slave_0) entered disabled state
[ 56.267268][ T4287] device bridge_slave_0 entered promiscuous mode
[ 56.283651][ T4280] team0: Port device team_slave_0 added
[ 56.315410][ T4287] bridge0: port 2(bridge_slave_1) entered blocking state
[ 56.325819][ T4287] bridge0: port 2(bridge_slave_1) entered disabled state
[ 56.334142][ T4287] device bridge_slave_1 entered promiscuous mode
[ 56.343257][ T4280] team0: Port device team_slave_1 added
[ 56.372206][ T4282] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 56.402420][ T4287] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 56.420248][ T4282] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 56.440455][ T4280] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 56.447720][ T4280] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.473693][ T4280] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 56.487893][ T4287] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 56.533479][ T4282] team0: Port device team_slave_0 added
[ 56.539689][ T4280] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 56.546754][ T4280] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.573230][ T4280] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 56.594456][ T4287] team0: Port device team_slave_0 added
[ 56.602314][ T4282] team0: Port device team_slave_1 added
[ 56.608951][ T4287] team0: Port device team_slave_1 added
[ 56.691407][ T4287] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 56.698492][ T4287] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.725618][ T1325] Bluetooth: hci0: command 0x0409 tx timeout
[ 56.730841][ T4287] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 56.758822][ T4282] batman_adv: batadv0: Adding interface: batadv_slave_0
[ 56.765962][ T4282] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.792135][ T4282] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[ 56.804905][ T4287] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 56.811997][ T4287] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.838340][ T4287] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 56.861601][ T4280] device hsr_slave_0 entered promiscuous mode
[ 56.869999][ T4280] device hsr_slave_1 entered promiscuous mode
[ 56.876525][ T4280] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 56.884126][ T4280] Cannot create hsr debugfs directory
[ 56.889965][ T4282] batman_adv: batadv0: Adding interface: batadv_slave_1
[ 56.897886][ T4282] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem.
[ 56.924225][ T4282] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[ 56.962446][ T1325] Bluetooth: hci4: command 0x0409 tx timeout
[ 56.968647][ T1325] Bluetooth: hci3: command 0x0409 tx timeout
[ 56.976527][ T1325] Bluetooth: hci2: command 0x0409 tx timeout
[ 56.982841][ T1325] Bluetooth: hci1: command 0x0409 tx timeout
[ 56.999404][ T4287] device hsr_slave_0 entered promiscuous mode
[ 57.006628][ T4287] device hsr_slave_1 entered promiscuous mode
[ 57.013535][ T4287] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 57.021192][ T4287] Cannot create hsr debugfs directory
[ 57.038889][ T4282] device hsr_slave_0 entered promiscuous mode
[ 57.045948][ T4282] device hsr_slave_1 entered promiscuous mode
[ 57.052607][ T4282] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 57.060149][ T4282] Cannot create hsr debugfs directory
[ 57.559092][ T156] netdevsim netdevsim3 netdevsim2 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[ 58.811067][ T1325] Bluetooth: hci0: command 0x041b tx timeout
[ 59.041110][ T1325] Bluetooth: hci1: command 0x041b tx timeout
[ 59.047247][ T1325] Bluetooth: hci2: command 0x041b tx timeout
[ 59.053966][ T1325] Bluetooth: hci3: command 0x041b tx timeout
[ 59.059996][ T1325] Bluetooth: hci4: command 0x041b tx timeout
[ 59.805329][ T156] netdevsim netdevsim3 netdevsim1 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[ 59.854671][ T156] netdevsim netdevsim3 netdevsim0 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[ 60.032000][ T4284] netdevsim netdevsim4 netdevsim0: renamed from eth0
[ 60.145354][ T4284] netdevsim netdevsim4 netdevsim1: renamed from eth1
[ 60.175388][ T4284] netdevsim netdevsim4 netdevsim2: renamed from eth2
[ 60.218825][ T4284] netdevsim netdevsim4 netdevsim3: renamed from eth3
[ 60.298731][ T4276] netdevsim netdevsim0 netdevsim0: renamed from eth0
[ 60.335900][ T4276] netdevsim netdevsim0 netdevsim1: renamed from eth1
[ 60.379016][ T4276] netdevsim netdevsim0 netdevsim2: renamed from eth2
[ 60.408259][ T4276] netdevsim netdevsim0 netdevsim3: renamed from eth3
[ 60.420742][ T4282] netdevsim netdevsim2 netdevsim0: renamed from eth0
[ 60.461988][ T4282] netdevsim netdevsim2 netdevsim1: renamed from eth1
[ 60.486442][ T4284] 8021q: adding VLAN 0 to HW filter on device bond0
[ 60.495312][ T4282] netdevsim netdevsim2 netdevsim2: renamed from eth2
[ 60.507248][ T4282] netdevsim netdevsim2 netdevsim3: renamed from eth3
[ 60.531131][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 60.538841][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 60.587521][ T4284] 8021q: adding VLAN 0 to HW filter on device team0
[ 60.643798][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 60.653573][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 60.662502][ T4245] bridge0: port 1(bridge_slave_0) entered blocking state
[ 60.669548][ T4245] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 60.677321][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 60.686237][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 60.695423][ T4245] bridge0: port 2(bridge_slave_1) entered blocking state
[ 60.702496][ T4245] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 60.710307][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 60.719928][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 60.762664][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 60.772815][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 60.782129][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 60.843832][ T4282] 8021q: adding VLAN 0 to HW filter on device bond0
[ 60.881329][ T4355] Bluetooth: hci0: command 0x040f tx timeout
[ 60.899620][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 60.908139][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 60.918057][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 60.927031][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_hsr: link becomes ready
[ 60.935984][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 60.944847][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 60.954270][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 60.965181][ T4284] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 61.042275][ T4276] 8021q: adding VLAN 0 to HW filter on device bond0
[ 61.052213][ T4282] 8021q: adding VLAN 0 to HW filter on device team0
[ 61.062160][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 61.070576][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 61.079267][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 61.089118][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 61.104552][ T154] bridge0: port 1(bridge_slave_0) entered blocking state
[ 61.111644][ T154] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 61.131125][ T4351] Bluetooth: hci4: command 0x040f tx timeout
[ 61.137242][ T4351] Bluetooth: hci3: command 0x040f tx timeout
[ 61.145520][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 61.153422][ T4351] Bluetooth: hci2: command 0x040f tx timeout
[ 61.158902][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 61.167519][ T4351] Bluetooth: hci1: command 0x040f tx timeout
[ 61.180666][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 61.189919][ T154] bridge0: port 2(bridge_slave_1) entered blocking state
[ 61.197021][ T154] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 61.206116][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 61.214963][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 61.223986][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 61.232709][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 61.254022][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 61.265327][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 61.275380][ T4276] 8021q: adding VLAN 0 to HW filter on device team0
[ 61.289422][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 61.298699][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 61.307519][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 61.316306][ T4245] bridge0: port 1(bridge_slave_0) entered blocking state
[ 61.323396][ T4245] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 61.332012][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 61.375228][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 61.384667][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 61.393525][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_hsr: link becomes ready
[ 61.403383][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 61.412107][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 61.420377][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 61.428988][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 61.437929][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 61.446559][ T4245] bridge0: port 2(bridge_slave_1) entered blocking state
[ 61.453737][ T4245] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 61.462023][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 61.470447][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 61.478253][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 61.492864][ T4287] netdevsim netdevsim3 netdevsim0: renamed from eth0
[ 61.508813][ T4282] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 61.529011][ T4287] netdevsim netdevsim3 netdevsim1: renamed from eth1
[ 61.540588][ T4245] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 61.574228][ T4284] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 61.587397][ T4287] netdevsim netdevsim3 netdevsim2: renamed from eth2
[ 61.608553][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 61.627076][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 61.640816][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 61.650319][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 61.666437][ T4276] hsr0: Slave A (hsr_slave_0) is not up; please bring it up to get a fully working HSR network
[ 61.684766][ T4276] hsr0: Slave B (hsr_slave_1) is not up; please bring it up to get a fully working HSR network
[ 61.709093][ T4287] netdevsim netdevsim3 netdevsim3: renamed from eth3
[ 61.725826][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 61.739216][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_hsr: link becomes ready
[ 61.755536][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 61.768354][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 61.780526][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 61.816281][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 62.051128][ T4280] netdevsim netdevsim1 netdevsim0: renamed from eth0
[ 62.063110][ T4280] netdevsim netdevsim1 netdevsim1: renamed from eth1
[ 62.105240][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 62.116784][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 62.124806][ T4280] netdevsim netdevsim1 netdevsim2: renamed from eth2
[ 62.137643][ T4282] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 62.170809][ T4276] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 62.189767][ T4280] netdevsim netdevsim1 netdevsim3: renamed from eth3
[ 62.254427][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 62.262182][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 62.269615][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 62.279060][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 62.339143][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 62.354043][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 62.384097][ T4284] device veth0_vlan entered promiscuous mode
[ 62.428241][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 62.437358][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 62.446705][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 62.456074][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 62.465251][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 62.474298][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 62.487612][ T4276] device veth0_vlan entered promiscuous mode
[ 62.525884][ T4287] 8021q: adding VLAN 0 to HW filter on device bond0
[ 62.541015][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 62.556345][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 62.568379][ T4284] device veth1_vlan entered promiscuous mode
[ 62.583609][ T4276] device veth1_vlan entered promiscuous mode
[ 62.622001][ T4287] 8021q: adding VLAN 0 to HW filter on device team0
[ 62.628909][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 62.639296][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 62.648200][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 62.656747][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 62.665324][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 62.677209][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 62.687737][ T4282] device veth0_vlan entered promiscuous mode
[ 62.738935][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 62.749872][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 62.766097][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 62.778464][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 62.813362][ T4282] device veth1_vlan entered promiscuous mode
[ 62.823329][ T4276] device veth0_macvtap entered promiscuous mode
[ 62.834250][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan0: link becomes ready
[ 62.846784][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 62.858562][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 62.873700][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 62.883271][ T3112] bridge0: port 1(bridge_slave_0) entered blocking state
[ 62.890352][ T3112] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 62.900453][ T4280] 8021q: adding VLAN 0 to HW filter on device bond0
[ 62.923812][ T4276] device veth1_macvtap entered promiscuous mode
[ 62.932937][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan1: link becomes ready
[ 62.942132][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 62.950087][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 62.958533][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 62.966951][ T4351] Bluetooth: hci0: command 0x0419 tx timeout
[ 62.968001][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 62.982787][ T3112] bridge0: port 2(bridge_slave_1) entered blocking state
[ 62.989865][ T3112] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 63.024766][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 63.034685][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 63.045481][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 63.055504][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 63.064235][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 63.073745][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 63.082245][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1: link becomes ready
[ 63.089766][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready
[ 63.098786][ T4284] device veth0_macvtap entered promiscuous mode
[ 63.108947][ T4282] device veth0_macvtap entered promiscuous mode
[ 63.117336][ T4276] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.129142][ T4276] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.140410][ T4276] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 63.195923][ T4284] device veth1_macvtap entered promiscuous mode
[ 63.204441][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 63.213334][ T4390] Bluetooth: hci1: command 0x0419 tx timeout
[ 63.219378][ T4390] Bluetooth: hci2: command 0x0419 tx timeout
[ 63.224860][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 63.226107][ T4390] Bluetooth: hci3: command 0x0419 tx timeout
[ 63.238943][ T4390] Bluetooth: hci4: command 0x0419 tx timeout
[ 63.239175][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 63.254229][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 63.263050][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 63.272048][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 63.282588][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 63.290866][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 63.300701][ T4276] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 63.311682][ T4276] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.325042][ T4276] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 63.334694][ T4282] device veth1_macvtap entered promiscuous mode
[ 63.343279][ T4280] 8021q: adding VLAN 0 to HW filter on device team0
[ 63.358023][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 63.366781][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 63.375361][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
[ 63.384815][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 63.393423][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 63.402386][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_hsr: link becomes ready
[ 63.410551][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 63.420758][ T4276] netdevsim netdevsim0 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.429678][ T4276] netdevsim netdevsim0 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.438387][ T4276] netdevsim netdevsim0 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.447468][ T4276] netdevsim netdevsim0 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.468549][ T4282] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.481637][ T4282] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.491784][ T4282] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.502419][ T4282] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.513787][ T4282] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 63.525548][ T4287] hsr0: Slave B (hsr_slave_1) is not up; please bring it up to get a fully working HSR network
[ 63.540440][ T4287] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 63.549464][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bridge: link becomes ready
[ 63.559142][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready
[ 63.568585][ T3112] bridge0: port 1(bridge_slave_0) entered blocking state
[ 63.575648][ T3112] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 63.584167][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bridge: link becomes ready
[ 63.593921][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready
[ 63.605624][ T3112] bridge0: port 2(bridge_slave_1) entered blocking state
[ 63.612702][ T3112] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 63.621756][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_bond: link becomes ready
[ 63.630502][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 63.639230][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 63.647883][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 63.656905][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 63.665334][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): bridge0: link becomes ready
[ 63.683848][ T4282] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 63.695414][ T4282] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.705744][ T4282] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 63.716584][ T4282] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.727930][ T4282] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 63.738247][ T4282] netdevsim netdevsim2 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.747183][ T4282] netdevsim netdevsim2 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.756045][ T4282] netdevsim netdevsim2 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.765396][ T4282] netdevsim netdevsim2 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 63.776720][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_bond: link becomes ready
[ 63.785826][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 63.795066][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
[ 63.890176][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.902132][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.912711][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.923338][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.933391][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 63.944105][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 63.956032][ T4284] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 63.969881][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_team: link becomes ready
[ 63.980444][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready
[ 63.988935][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_team: link becomes ready
[ 63.998001][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready
[ 64.006876][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_hsr: link becomes ready
[ 64.015207][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready
[ 64.023644][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_hsr: link becomes ready
[ 64.033256][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready
[ 64.043214][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 64.051839][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 64.060445][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
[ 64.079410][ T4280] IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready
[ 64.102624][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 64.113330][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 64.128548][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 64.139721][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 64.156676][ T4284] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 64.168723][ T4284] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 64.184064][ T4284] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 64.212694][ T4284] netdevsim netdevsim4 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 64.227967][ T4284] netdevsim netdevsim4 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 64.238964][ T4284] netdevsim netdevsim4 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 64.248905][ T4284] netdevsim netdevsim4 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 64.259450][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 64.269657][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
[ 64.353149][ T9] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 64.364527][ T9] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 64.376594][ T4280] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 64.395897][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 64.399399][ T9] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 64.408068][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 64.416370][ T9] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 64.425038][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 64.433312][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready
[ 64.440699][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready
[ 64.448440][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 64.497809][ T4287] 8021q: adding VLAN 0 to HW filter on device batadv0
[ 64.505118][ T3112] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 64.514135][ T3112] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 64.514909][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 64.530147][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 64.539922][ T154] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
2025/10/25 08:28:09 executed programs: 10
[ 64.576353][ T3112] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 64.590170][ T3112] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 64.590220][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 64.608666][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 64.655253][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 64.670372][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 64.683432][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 64.691718][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_virt_wifi: link becomes ready
[ 64.700395][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready
[ 64.720753][ T4280] device veth0_vlan entered promiscuous mode
[ 64.733153][ T3112] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 64.747378][ T3112] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 64.777925][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_vlan: link becomes ready
[ 64.806419][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready
[ 64.819799][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 64.838869][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready
[ 64.849982][ T4411] IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready
[ 64.951479][ T4287] device veth0_vlan entered promiscuous mode
[ 64.965787][ T4280] device veth1_vlan entered promiscuous mode
[ 65.005435][ T4287] device veth1_vlan entered promiscuous mode
[ 65.024569][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan0: link becomes ready
[ 65.024651][ T4411] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 65.050401][ T4411] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 65.058617][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan1: link becomes ready
[ 65.082000][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan0: link becomes ready
[ 65.090816][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 65.113838][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 65.126145][ T4280] device veth0_macvtap entered promiscuous mode
[ 65.158738][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvlan1: link becomes ready
[ 65.197168][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 65.229090][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 65.260423][ T4287] device veth0_macvtap entered promiscuous mode
[ 65.304476][ T4280] device veth1_macvtap entered promiscuous mode
[ 65.326104][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 65.335917][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_macvtap: link becomes ready
[ 65.372509][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready
[ 65.387769][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready
[ 65.420198][ T4287] device veth1_macvtap entered promiscuous mode
[ 65.482679][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.519204][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.537433][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.560755][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.581709][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.598600][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.609752][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.620639][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.633683][ T4280] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 65.643079][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.664762][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.693447][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.707919][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.720193][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.731010][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.742017][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.754148][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.764651][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_0
[ 65.775616][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.787223][ T4287] batman_adv: batadv0: Interface activated: batadv_slave_0
[ 65.807748][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): macsec0: link becomes ready
[ 65.818447][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 65.830190][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 65.839957][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_0: link becomes ready
[ 65.849185][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready
[ 65.870398][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 65.892824][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.903074][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 65.914129][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.929481][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 65.940145][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.950245][ T4280] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 65.960870][ T4280] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 65.979408][ T4280] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 65.989683][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 66.015036][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 66.025138][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 66.040327][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 66.050331][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 66.060811][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 66.071326][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 66.082027][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 66.092570][ T4287] batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3f) already exists on: batadv_slave_1
[ 66.103178][ T4287] batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems!
[ 66.116166][ T4287] batman_adv: batadv0: Interface activated: batadv_slave_1
[ 66.167394][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 66.176975][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
[ 66.216355][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready
[ 66.234602][ T9] IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready
[ 66.258147][ T4280] netdevsim netdevsim1 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.286889][ T4280] netdevsim netdevsim1 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.296737][ T4280] netdevsim netdevsim1 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.311460][ T4280] netdevsim netdevsim1 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.333095][ T4287] netdevsim netdevsim3 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.342646][ T4287] netdevsim netdevsim3 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.352841][ T4287] netdevsim netdevsim3 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.363444][ T4287] netdevsim netdevsim3 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[ 66.554770][ T9] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 66.570761][ T9] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 66.583727][ T144] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 66.773609][ T9] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 66.816845][ T9] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 66.863711][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 66.928930][ T3112] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 66.961316][ T3112] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 66.988512][ T4414] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 67.050491][ T4411] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[ 67.097318][ T156] device hsr_slave_0 left promiscuous mode
[ 67.108968][ T4411] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[ 67.131714][ T156] device hsr_slave_1 left promiscuous mode
[ 67.147464][ T156] batman_adv: batadv0: Interface deactivated: batadv_slave_0
[ 67.174389][ T156] batman_adv: batadv0: Removing interface: batadv_slave_0
[ 67.203532][ T156] batman_adv: batadv0: Interface deactivated: batadv_slave_1
[ 67.220348][ T156] batman_adv: batadv0: Removing interface: batadv_slave_1
[ 67.233214][ T156] device bridge_slave_1 left promiscuous mode
[ 67.256349][ T156] bridge0: port 2(bridge_slave_1) entered disabled state
[ 67.300043][ T156] device bridge_slave_0 left promiscuous mode
[ 67.319775][ T156] bridge0: port 1(bridge_slave_0) entered disabled state
[ 67.399439][ T156] device veth1_macvtap left promiscuous mode
[ 67.444450][ T156] device veth0_macvtap left promiscuous mode
[ 67.474371][ T156] device veth1_vlan left promiscuous mode
[ 67.480329][ T156] device veth0_vlan left promiscuous mode
[ 68.371778][ T156] team0 (unregistering): Port device team_slave_1 removed
[ 68.423877][ T156] team0 (unregistering): Port device team_slave_0 removed
[ 68.484449][ T156] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface
[ 68.580430][ T156] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface
[ 68.909308][ T156] bond0 (unregistering): Released all slaves
[ 69.138136][ T3112] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
2025/10/25 08:28:14 executed programs: 220
[ 71.134842][ T1422] ieee802154 phy0 wpan0: encryption failed: -22
[ 71.152739][ T1422] ieee802154 phy1 wpan1: encryption failed: -22
2025/10/25 08:28:19 executed programs: 459
[ 76.245080][ T1108] cfg80211: failed to load regulatory.db
[ 78.652364][ C1] ------------[ cut here ]------------
[ 78.658010][ C1] WARNING: CPU: 1 PID: 156 at mm/maccess.c:226 copy_from_user_nofault+0x160/0x1c0
[ 78.667210][ C1] Modules linked in:
[ 78.671093][ C1] CPU: 1 PID: 156 Comm: kworker/u4:3 Not tainted syzkaller #0
[ 78.678529][ C1] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
[ 78.688564][ C1] Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet
[ 78.696373][ C1] RIP: 0010:copy_from_user_nofault+0x160/0x1c0
[ 78.702508][ C1] Code: 24 45 31 f6 31 ff 89 de e8 dd f6 d8 ff 85 db 48 c7 c0 f2 ff ff ff 49 0f 44 c6 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 60 f3 d8 ff <0f> 0b e9 1c ff ff ff 44 89 e1 80 e1 07 80 c1 03 38 c1 0f 8c ea fe
[ 78.722186][ C1] RSP: 0018:ffffc90000dd0c10 EFLAGS: 00010006
[ 78.728242][ C1] RAX: ffffffff819ed730 RBX: 0000000000000000 RCX: ffff88801d769dc0
[ 78.736192][ C1] RDX: 0000000000010000 RSI: 0000000000000000 RDI: 0000000000000000
[ 78.744142][ C1] RBP: 0000000000000000 R08: dffffc0000000000 R09: ffffed1003aed3b9
[ 78.752095][ C1] R10: ffffed1003aed3b9 R11: 1ffff11003aed3b8 R12: ffff88801d76b548
[ 78.760047][ C1] R13: 00007ffffffff000 R14: ffffc90000dd0c88 R15: 0000000000000000
[ 78.767997][ C1] FS: 0000000000000000(0000) GS:ffff8880b9100000(0000) knlGS:0000000000000000
[ 78.776905][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 78.783469][ C1] CR2: 00007f91eb1f06c0 CR3: 000000000be8e000 CR4: 00000000003506e0
[ 78.791422][ C1] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 78.799375][ C1] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 78.807331][ C1] Call Trace:
[ 78.810591][ C1]
[ 78.813420][ C1] bpf_probe_read_compat+0xdd/0x170
[ 78.818610][ C1] bpf_prog_f3c4d654356a1293+0x34/0x710
[ 78.824136][ C1] bpf_trace_run2+0x15b/0x2d0
[ 78.828793][ C1] ? bpf_trace_run1+0x2d0/0x2d0
[ 78.833628][ C1] ? perf_trace_tlb_flush+0x340/0x340
[ 78.838987][ C1] __traceiter_tlb_flush+0x69/0xb0
[ 78.844079][ C1] trace_tlb_flush+0xe6/0x110
[ 78.848734][ C1] switch_mm_irqs_off+0x6e3/0x9a0
[ 78.853739][ C1] ? switch_mm+0x120/0x120
[ 78.858132][ C1] ? lockdep_softirqs_on+0x2f4/0x570
[ 78.863398][ C1] ? lockdep_hardirqs_on_prepare+0x760/0x760
[ 78.869356][ C1] ? __irq_exit_rcu+0x12f/0x220
[ 78.874184][ C1] flush_tlb_func+0x1bc/0x510
[ 78.878840][ C1] ? irqtime_account_irq+0x16b/0x1b0
[ 78.884198][ C1] ? native_flush_tlb_multi+0xd0/0xd0
[ 78.889551][ C1] ? kvm_sched_clock_read+0x14/0x40
[ 78.894727][ C1] ? native_flush_tlb_multi+0xd0/0xd0
[ 78.900074][ C1] flush_smp_call_function_queue+0x2a9/0x760
[ 78.906036][ C1] __sysvec_call_function_single+0x98/0x240
[ 78.911911][ C1] sysvec_call_function_single+0x98/0xc0
[ 78.917526][ C1]
[ 78.920450][ C1]
[ 78.923377][ C1] asm_sysvec_call_function_single+0x16/0x20
[ 78.929355][ C1] RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x60
[ 78.935410][ C1] Code: 84 00 00 00 00 00 53 48 89 fb e8 17 00 00 00 48 8b 3d 10 d2 f1 0b 48 89 de 5b e9 07 9e 43 00 00 00 cc cc 00 00 cc 48 8b 04 24 <65> 48 8b 0d 24 a5 8a 7e 65 8b 15 25 a5 8a 7e 81 e2 00 01 ff 00 74
[ 78.955004][ C1] RSP: 0018:ffffc90001fb7a38 EFLAGS: 00000202
[ 78.961063][ C1] RAX: ffffffff897a0a22 RBX: ffff8880277842c0 RCX: ffff88801d769d01
[ 78.969017][ C1] RDX: 0000000000000000 RSI: ffffffff8a59a860 RDI: ffffffff8a59a820
[ 78.976970][ C1] RBP: ffffc90001fb7b80 R08: dffffc0000000000 R09: fffffbfff1ff7a19
[ 78.984934][ C1] R10: fffffbfff1ff7a19 R11: 1ffffffff1ff7a18 R12: fffffffffffffe38
[ 78.992887][ C1] R13: dffffc0000000000 R14: 0000000000000001 R15: dffffc0000000000
[ 79.000849][ C1] ? batadv_iv_ogm_schedule+0x4e2/0xe90
[ 79.006384][ C1] batadv_iv_ogm_schedule+0x4e2/0xe90
[ 79.011755][ C1] ? batadv_iv_send_outstanding_bat_ogm_packet+0x840/0x840
[ 79.018932][ C1] ? batadv_send_skb_packet+0x392/0x5f0
[ 79.024461][ C1] batadv_iv_send_outstanding_bat_ogm_packet+0x72d/0x840
[ 79.032860][ C1] process_one_work+0x863/0x1000
[ 79.037790][ C1] ? worker_detach_from_pool+0x240/0x240
[ 79.043405][ C1] ? lockdep_hardirqs_off+0x70/0x100
[ 79.048672][ C1] ? _raw_spin_lock_irq+0xab/0xe0
[ 79.053675][ C1] ? _raw_spin_lock_irqsave+0xf0/0xf0
[ 79.059028][ C1] ? wq_worker_running+0x97/0x170
[ 79.064133][ C1] worker_thread+0xaa8/0x12a0
[ 79.068795][ C1] ? lockdep_hardirqs_on+0x94/0x140
[ 79.073977][ C1] ? lockdep_hardirqs_on+0x94/0x140
[ 79.079159][ C1] ? _raw_spin_unlock_irqrestore+0xaa/0x100
[ 79.085049][ C1] kthread+0x436/0x520
[ 79.089097][ C1] ? rcu_lock_release+0x20/0x20
[ 79.093926][ C1] ? kthread_blkcg+0xd0/0xd0
[ 79.098552][ C1] ret_from_fork+0x1f/0x30
[ 79.102960][ C1]
[ 79.105971][ C1] Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 79.113227][ C1] CPU: 1 PID: 156 Comm: kworker/u4:3 Not tainted syzkaller #0
[ 79.120661][ C1] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
[ 79.130695][ C1] Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet
[ 79.138746][ C1] Call Trace:
[ 79.142008][ C1]
[ 79.144833][ C1] dump_stack_lvl+0x168/0x230
[ 79.149494][ C1] ? show_regs_print_info+0x20/0x20
[ 79.154675][ C1] ? load_image+0x3b0/0x3b0
[ 79.159165][ C1] panic+0x2c9/0x7f0
[ 79.163043][ C1] ? bpf_jit_dump+0xd0/0xd0
[ 79.167532][ C1] ? ret_from_fork+0x1f/0x30
[ 79.172110][ C1] ? copy_from_user_nofault+0x160/0x1c0
[ 79.177648][ C1] __warn+0x248/0x2b0
[ 79.181626][ C1] ? copy_from_user_nofault+0x160/0x1c0
[ 79.187156][ C1] report_bug+0x1b7/0x2e0
[ 79.191477][ C1] handle_bug+0x3a/0x70
[ 79.195638][ C1] exc_invalid_op+0x16/0x40
[ 79.200139][ C1] asm_exc_invalid_op+0x16/0x20
[ 79.204974][ C1] RIP: 0010:copy_from_user_nofault+0x160/0x1c0
[ 79.211113][ C1] Code: 24 45 31 f6 31 ff 89 de e8 dd f6 d8 ff 85 db 48 c7 c0 f2 ff ff ff 49 0f 44 c6 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 60 f3 d8 ff <0f> 0b e9 1c ff ff ff 44 89 e1 80 e1 07 80 c1 03 38 c1 0f 8c ea fe
[ 79.230710][ C1] RSP: 0018:ffffc90000dd0c10 EFLAGS: 00010006
[ 79.236771][ C1] RAX: ffffffff819ed730 RBX: 0000000000000000 RCX: ffff88801d769dc0
[ 79.244729][ C1] RDX: 0000000000010000 RSI: 0000000000000000 RDI: 0000000000000000
[ 79.252683][ C1] RBP: 0000000000000000 R08: dffffc0000000000 R09: ffffed1003aed3b9
[ 79.260638][ C1] R10: ffffed1003aed3b9 R11: 1ffff11003aed3b8 R12: ffff88801d76b548
[ 79.268599][ C1] R13: 00007ffffffff000 R14: ffffc90000dd0c88 R15: 0000000000000000
[ 79.276563][ C1] ? copy_from_user_nofault+0x160/0x1c0
[ 79.282108][ C1] bpf_probe_read_compat+0xdd/0x170
[ 79.287295][ C1] bpf_prog_f3c4d654356a1293+0x34/0x710
[ 79.292825][ C1] bpf_trace_run2+0x15b/0x2d0
[ 79.297488][ C1] ? bpf_trace_run1+0x2d0/0x2d0
[ 79.302324][ C1] ? perf_trace_tlb_flush+0x340/0x340
[ 79.307690][ C1] __traceiter_tlb_flush+0x69/0xb0
[ 79.312788][ C1] trace_tlb_flush+0xe6/0x110
[ 79.317448][ C1] switch_mm_irqs_off+0x6e3/0x9a0
[ 79.322458][ C1] ? switch_mm+0x120/0x120
[ 79.326978][ C1] ? lockdep_softirqs_on+0x2f4/0x570
[ 79.332259][ C1] ? lockdep_hardirqs_on_prepare+0x760/0x760
[ 79.338273][ C1] ? __irq_exit_rcu+0x12f/0x220
[ 79.343112][ C1] flush_tlb_func+0x1bc/0x510
[ 79.347773][ C1] ? irqtime_account_irq+0x16b/0x1b0
[ 79.353047][ C1] ? native_flush_tlb_multi+0xd0/0xd0
[ 79.358407][ C1] ? kvm_sched_clock_read+0x14/0x40
[ 79.363597][ C1] ? native_flush_tlb_multi+0xd0/0xd0
[ 79.368951][ C1] flush_smp_call_function_queue+0x2a9/0x760
[ 79.374924][ C1] __sysvec_call_function_single+0x98/0x240
[ 79.380803][ C1] sysvec_call_function_single+0x98/0xc0
[ 79.386421][ C1]
[ 79.389341][ C1]
[ 79.392257][ C1] asm_sysvec_call_function_single+0x16/0x20
[ 79.398220][ C1] RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x60
[ 79.404267][ C1] Code: 84 00 00 00 00 00 53 48 89 fb e8 17 00 00 00 48 8b 3d 10 d2 f1 0b 48 89 de 5b e9 07 9e 43 00 00 00 cc cc 00 00 cc 48 8b 04 24 <65> 48 8b 0d 24 a5 8a 7e 65 8b 15 25 a5 8a 7e 81 e2 00 01 ff 00 74
[ 79.423862][ C1] RSP: 0018:ffffc90001fb7a38 EFLAGS: 00000202
[ 79.429916][ C1] RAX: ffffffff897a0a22 RBX: ffff8880277842c0 RCX: ffff88801d769d01
[ 79.437874][ C1] RDX: 0000000000000000 RSI: ffffffff8a59a860 RDI: ffffffff8a59a820
[ 79.445940][ C1] RBP: ffffc90001fb7b80 R08: dffffc0000000000 R09: fffffbfff1ff7a19
[ 79.453901][ C1] R10: fffffbfff1ff7a19 R11: 1ffffffff1ff7a18 R12: fffffffffffffe38
[ 79.461858][ C1] R13: dffffc0000000000 R14: 0000000000000001 R15: dffffc0000000000
[ 79.469827][ C1] ? batadv_iv_ogm_schedule+0x4e2/0xe90
[ 79.475371][ C1] batadv_iv_ogm_schedule+0x4e2/0xe90
[ 79.480733][ C1] ? batadv_iv_send_outstanding_bat_ogm_packet+0x840/0x840
[ 79.487912][ C1] ? batadv_send_skb_packet+0x392/0x5f0
[ 79.493443][ C1] batadv_iv_send_outstanding_bat_ogm_packet+0x72d/0x840
[ 79.500467][ C1] process_one_work+0x863/0x1000
[ 79.505399][ C1] ? worker_detach_from_pool+0x240/0x240
[ 79.511011][ C1] ? lockdep_hardirqs_off+0x70/0x100
[ 79.516293][ C1] ? _raw_spin_lock_irq+0xab/0xe0
[ 79.521299][ C1] ? _raw_spin_lock_irqsave+0xf0/0xf0
[ 79.526655][ C1] ? wq_worker_running+0x97/0x170
[ 79.531661][ C1] worker_thread+0xaa8/0x12a0
[ 79.536331][ C1] ? lockdep_hardirqs_on+0x94/0x140
[ 79.541524][ C1] ? lockdep_hardirqs_on+0x94/0x140
[ 79.546715][ C1] ? _raw_spin_unlock_irqrestore+0xaa/0x100
[ 79.552603][ C1] kthread+0x436/0x520
[ 79.556656][ C1] ? rcu_lock_release+0x20/0x20
[ 79.561492][ C1] ? kthread_blkcg+0xd0/0xd0
[ 79.566070][ C1] ret_from_fork+0x1f/0x30
[ 79.570481][ C1]
[ 79.573727][ C1] Kernel Offset: disabled
[ 79.578131][ C1] Rebooting in 86400 seconds..